Chrysler RG Voyager. Manual — part 287
Symptom:
GENERAL MICROPHONE FAULT
POSSIBLE CAUSES
HANDS FREE MODULE
MICROPHONE CIRCUITS OPEN
MICROPHONE CIRCUITS SHORT TO GROUND
MICROPHONE CIRCUITS SHORT TO VOLTAGE
MICROPHONE CIRCUITS SHORTED TOGETHER
REAR VIEW MIRROR
INTERMITTENT CONDITION
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Attempt to make a phone call using the system.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display this DTC?
All
Yes
→ Go To 2
No
→ Go To 7
2
Turn the ignition off.
Disconnect the Rear View Mirror C2 harness connector.
Disconnect the Hands Free Module C1 harness connector.
Measure the resistance of each Microphone circuit between the HFM connector and
the rear view mirror connector.
Is the resistance below 10.0 ohms for each measurement?
All
Yes
→ Go To 3
No
→ Repair the Microphone circuits for an open.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Disconnect the Rear View Mirror C2 harness connector.
Disconnect the Hands Free Module C1 harness connector.
Measure the resistance between ground and each Microphone circuit.
Is the resistance above 1000.0 ohms for each measurement?
All
Yes
→ Go To 4
No
→ Repair the Microphone circuits for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
1117
TELECOMMUNICATION
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the Rear View Mirror C2 harness connector.
Disconnect the Hands Free Module C1 harness connector.
Turn the ignition on.
Measure the voltage of each Microphone circuit.
Is the voltage below 1.0 volt for each measurement?
All
Yes
→ Go To 5
No
→ Repair the Microphone circuits for a short to voltage.
Perform BODY VERIFICATION TEST - VER 1.
5
Turn the ignition off.
Disconnect the Rear View Mirror C2 harness connector.
Disconnect the Hands Free Module C1 harness connector.
Measure the resistance between each Microphone circuit in the rear view mirror
harness connector.
Is the resistance above 1000 ohms for each measurement?
All
Yes
→ Go To 6
No
→ Refer the Microphone circuits for a short together.
Perform BODY VERIFICATION TEST - VER 1.
6
Replace the Rear View Mirror in accordance with the Service Information.
Turn the ignition on.
With the DRBIII
t, erase DTC’s.
Attempt to make a phone call using the system.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display this DTC?
All
Yes
→ Inspect the wiring and connectors for damage or shorted circuits.
Repair as necessary. If ok, replace and program the Hands Free
Module in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test complete.
Perform BODY VERIFICATION TEST - VER 1.
7
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, wiggle the wiring
harnesses. This is to try and duplicate the failure.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
1118
TELECOMMUNICATION
GENERAL MICROPHONE FAULT —
Continued
Symptom:
IGNITION POWER MESSAGE NOT RECEIVED
When Monitored and Set Condition:
IGNITION POWER MESSAGE NOT RECEIVED
When Monitored:
With the ignition on.
Set Condition:
The Hands Free Module does not receive an Ignition Power Status
message from the BCM.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE BCM
MODULE
TEST
ACTION
APPLICABILITY
1
Start and idle the engine.
With the DRBIII
t, attempt to I/D and communicate with the BCM.
Was the DRBIII
t able to I/D or communicate with the BCM?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
2
With the DRBIII
t, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRBIII
t, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace and program the Hands Free Module in accordance with
the service information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
1119
TELECOMMUNICATION
Symptom List:
LEFT AUDIO INPUT SHORT TO GROUND
LEFT AUDIO INPUT SHORT TO VOLTAGE
LEFT AUDIO OUTPUT 1 SHORT TO GROUND
LEFT AUDIO OUTPUT 1 SHORT TO VOLTAGE
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be LEFT AUDIO INPUT SHORT TO
GROUND.
When Monitored and Set Condition:
LEFT AUDIO INPUT SHORT TO GROUND
When Monitored:
With the ignition on
Set Condition:
The Hands Free Module detects low voltage on the input circuit.
LEFT AUDIO INPUT SHORT TO VOLTAGE
When Monitored:
With the ignition on.
Set Condition:
The Hands Free Module detects high voltage on the input circuit.
LEFT AUDIO OUTPUT 1 SHORT TO GROUND
When Monitored:
With the ignition on.
Set Condition:
The Hands Free Module detects a short to ground on the Left Audio
Output circuit.
LEFT AUDIO OUTPUT 1 SHORT TO VOLTAGE
When Monitored:
With the ignition on.
Set Condition:
The Hands Free Module detects a short to voltage on the Left Audio
Output circuit.
POSSIBLE CAUSES
HANDS FREE MODULE
LEFT AUDIO OUTPUT AND RIGHT AUDIO OUTPUT CIRCUITS SHORTED TOGETHER
LEFT AUDIO OUTPUT CIRCUIT OPEN
LEFT AUDIO OUTPUT CIRCUIT SHORT TO GROUND
LEFT AUDIO OUTPUT CIRCUIT SHORT TO VOLTAGE
INTERMITTENT CONDITION
1120
TELECOMMUNICATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст