Chrysler Pacifica. Manual — part 834
![](/vehicles/ged/ing/kee/plverkabys.png)
INSTALLATION
(1) Place seat back foam and cover together.
(2) Work the foam and cover under recliner torque
rod (Fig. 32).
(3) Place seat foam/cover onto seat frame (Fig. 31).
(4) Route to under side of cushion pad and connect
heat seat wire harness three attachments.
NOTE: Use care not to damage wire harness during
install procedure.
(5) Remove seat back foam/cover and heating har-
ness assembly together (keep trim attached to foam
pad).
(6) Feed back harness through hole in shield and
connect wiring harness (for heated seats) at inner
shield.
(7) Install trim ring (Fig. 29).
(8) Engage inner J-straps to trim ring (Fig. 30).
(9) Install screws attaching trim ring to seat back
frame (Fig. 28) and (Fig. 29).
(10) Engage outer J-straps at seat back (Fig. 27).
(11) Install three screws attaching outboard side
shield.
(12) Install two screws attaching inboard side
shield.
(13) Push outboard side handle on retainer tab till
it locks.
(14) Install cushion and cover onto seat pan.
(15) Install three screws attaching inner side
shield hinge area.
(16) Install two screws attaching outer side shield
buckle side.
(17) Install seat inner panel. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT INNER PANEL -
INSTALLATION)
(18) Install armrest. (Refer to 23 - BODY/SEATS/
SEAT ARMREST - INSTALLATION).
(19) Connect heat element wire harness.
(20) Install second row seat. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT - INSTALLATION).
(21) Install headrest and sleeves (Refer to 23 -
BODY/SEATS/HEADREST - INSTALLATION).
(22) Connect battery negative cable.
SECOND ROW SEAT LOAD
FLOOR PANEL
REMOVAL
(1) Fold second row seat down flat (Fig. 33).
(2) Using a trim stick C-4755 or equivalent, disen-
gage the seat back load floor panel push pins by pull-
ing away from seat back.
INSTALLATION
(1) Place second row seat load floor panel into
position (Fig. 33).
(2) Press on seat back load floor panel to engage
push pins to seat back frame.
SECOND ROW SEAT BACK
FRAME/RECLINER/TORQUE
ROD/CRAS ASSEMBLY
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove headrest and sleeves. (Refer to 23 -
BODY/SEATS/HEADREST - REMOVAL).
(3) Remove second row seat. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT - REMOVAL).
(4) Disconnect heat element wire harness.
(5) Remove armrest. (Refer to 23 - BODY/SEATS/
SEAT ARMREST - REMOVAL).
(6) Remove seat inner panel. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT INNER PANEL -
REMOVAL).
(7) Remove outboard side handle (lift on back side
of handle where it engages retainer tab and pull off).
(8) Remove two screws attaching inboard side
shield.
(9) Remove three screws attaching outboard side
shield.
(10) Disengage outer J-straps at seat back (Fig.
34).
Fig. 33 SEAT BACK LOAD FLOOR PANEL
1 - LOAD FLOOR PANEL
2 - HOOK AND LOOP WITH STRAP
CS
SEATS
23 - 131
SECOND ROW SEAT BACK CUSHION FOAM/COVER (Continued)
![](/vehicles/ged/ing/kee/nle.png)
(11) Remove screws attaching trim ring to seat
back frame (Fig. 35) and (Fig. 36).
(12) Remove trim ring (Fig. 36).
(13) Disengage inner J-straps from trim ring (Fig.
37).
Fig. 34 SECOND ROW SEAT BACK COVER
1 - SECOND ROW SEAT BACK COVER
2 - J-STRAPS
3 - SECOND ROW SEAT ASSEMBLY
Fig. 35 SECOND ROW SEAT BACK TRIM RING
1 - TRIM RING
2 - J-STRAPS
3 - ATTACHING SCREWS
Fig. 36 TRIM RING FOR SEAT BACK FRAME
1 - SECOND ROW SEAT BACK FRAME
2 - TRIM RING FOR SEAT BACK FRAME
3 - SEAT BACK CUSHION
Fig. 37 SEAT BACK J-STRAPS
1 - J-STRAPS
2 - SECOND ROW SEAT BACK COVER
23 - 132
SEATS
CS
SECOND ROW SEAT BACK FRAME/RECLINER/TORQUE ROD/CRAS ASSEMBLY (Continued)
![](/vehicles/ged/ing/kee/uci.png)
(14) Disconnect wiring harness (for heated seats)
at inner shield and feed back harness through hole in
shield (Fig. 38).
(15) Remove seat back foam/cover and heating har-
ness assembly together (keep trim attached to foam
pad).
(16) Work the foam and cover under recliner
torque rod and remove seat foam/cover (Fig. 39) and
(Fig. 40).
(17) Remove upper recliner bolts to seat back
frame (Fig. 41) and (Fig. 42).
Fig. 38 HEATED SEAT WIRE HARNESS
1 - Wire harness fasteners
Fig. 39 SECOND ROW SEAT BACK CUSHION AND
COVER REMOVAL
1 - SECOND ROW SEAT RECLINER TORQUE ROD
2 - SEAT BACK FOAM/COVER
Fig. 40 SECOND ROW SEAT BACK FRAME AND
COVER
1 - SEAT BACK FOAM PAD
2 - SEAT BACK COVER
3 - SEAT BACK FRAME
Fig. 41 SECOND ROW SEAT BACK FRAME
OUTBOARD SIDE BOLTS
1 - SEAT BACK FRAME
2 - ATTACHING BOLTS
CS
SEATS
23 - 133
SECOND ROW SEAT BACK FRAME/RECLINER/TORQUE ROD/CRAS ASSEMBLY (Continued)
![](/vehicles/ged/ing/kee/soosthin.png)
NOTE: Use care not to damage wire harness during
removal procedure.
(18) Disconnect heat seat wire harness from three
attachments and route to under side of cushion pad.
(19) Disconnect the J-strap and push pin fasteners
at the rear of seat cushion pan (Fig. 43) and (Fig.
44).
(20) Remove cushion foam and cover from seat pan
(Fig. 45).
Fig. 42 SECOND ROW SEAT BACK FRAME
INBOARD SIDE BOLTS
1 - SEAT BACK FRAME
2 - INBOARD ATTACHING BOLTS
Fig. 43 SEAT CUSHION REAR J-STRAP
1 - HEATED SEAT WIRE HARNESS
2 - J-STRAP
Fig. 44 SEAT CUSHION REAR PUSH PINS
1 - PUSH PIN FASTENERS
Fig. 45 SEAT CUSHION COVER AND FOAM PAD
1 - J-STRAPS
2 - HEATED SEAT WIRE HARNESS
3 - SEAT CUSHION PAN ASSEMBLY
4 - SEAT CUSHION FOAM AND COVER
23 - 134
SEATS
CS
SECOND ROW SEAT BACK FRAME/RECLINER/TORQUE ROD/CRAS ASSEMBLY (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст