Chrysler Pacifica. Manual — part 838
(9) Remove seat cushion cover and foam pad from
the seat pan (Fig. 85) and (Fig. 86).
(10) Remove one screw (at the rear of the cushion
pan) attaching the cushion slider (Fig. 87).
(11) Remove cushion slider.
INSTALLATION
(1) Place cushion slider into position (Fig. 87).
(2) Install cushion attaching screw to cushion pan.
(3) Install seat cushion cover and foam pad onto
seat pan (Fig. 85) and (Fig. 86).
(4) Engage J-straps (Fig. 84).
(5) Install cushion assembly onto the seat risers.
(6) Install cushion assembly by sliding the front
links onto the riser pins and twisting the cushion
assembly to engage the rear sliders onto the riser
tracks (Fig. 83).
(7) Install two bolts attaching front cushion pan to
link and risers (Fig. 81). Tighten to 29 N·m (21 ft.
lbs.) torque.
(8) Install drive link assembly.
(9) Install two bolts attaching drive link assembly
(Fig. 81). Tighten to 10 N·m (7 ft. lbs.) torque.
(10) Install third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - INSTALLATION).
(11) Install rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE TRAY -
INSTALLATION).
(12) Close liftgate.
Fig. 85 THIRD ROW SEAT CUSHION
1 - SEAT CUSHION PAN
2 - SEAT CUSHION FOAM AND COVER
3 - J-STRAPS
Fig. 86 THIRD ROW SEAT CUSHION FOAM PAD
1 - SEAT CUSHION COVER
2 - SEAT CUSHION FOAM PAD
Fig. 87 THIRD ROW SEAT SLIDER ATTACHING
SCREW
1 - ATTACHING SCREW
2 - SLIDER GUIDE PIN
CS
SEATS
23 - 147
THIRD ROW CUSHION SLIDER (Continued)
THIRD ROW OUTBOARD
LATCH ASSEMBLY
REMOVAL
(1) Open liftgate.
(2) Remove rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE BIN -
REMOVAL).
(3) Remove third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - REMOVAL).
(4) Remove two bolts (on outboard side of seat)
attaching drive link assembly (Fig. 88).
(5) Remove drive link assembly.
(6) Remove outboard seat back shield (Fig. 89).
(7) Disconnect fold flat cable from outboard fold
flat mechanism (Fig. 90).
(8) Remove two bolts attaching outboard fold flat
mechanism to outer seat back. Remove two nuts
attaching outboard fold flat mechanism to outboard
riser (Fig. 91).
(9) Remove outboard fold flat mechanism.
INSTALLATION
(1) Place outboard fold flat mechanism into posi-
tion.
(2) Install two bolts attaching outboard fold flat
mechanism to outer seat back. Install two nuts
attaching outboard fold flat mechanism to outboard
riser (Fig. 91).
(3) Connect fold flat cable to outboard fold flat
mechanism (Fig. 90).
(4) Install outboard seat back shield (Fig. 89).
(5) Place drive link assembly into position.
Fig. 88 DRIVE LINK AND SHIELD
1 - DRIVE LINK AND SHIELD
Fig. 89 OUTBOARD SEAT BACK SHIELD
1 - SHIELD
Fig. 90 FOLD FLAT CABLE ATTACHING POINTS
1 - FOLD FLAT MECHANISM
2 - FOLD FLAT CABLE ATTACHING POINTS
Fig. 91 FOLD FLAT MECHANISM
1 - FOLD FLAT MECHANISM
23 - 148
SEATS
CS
(6) Install two bolts (on outboard side of seat)
attaching drive link assembly (Fig. 88). Tighten to 10
N·m (7 ft. lbs.) torque.
(7) Install third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - INSTALLATION).
(8) Install rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE TRAY -
INSTALLATION).
(9) Close liftgate.
THIRD ROW INBOARD PIVOT
REMOVAL
(1) Open liftgate.
(2) Remove rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE BIN -
REMOVAL).
(3) Remove third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - REMOVAL).
(4) Using finger, disengage fold flat cable from
handle (Fig. 92).
(5) Release tab attaching fold flat handle to load
floor panel (Fig. 93).
(6) Disconnect fold flat cable from handle and
remove handle.
(7) Remove load floor panel by using a trim tool
and lifting up the edges to disengage the push pins
(Fig. 94).
Fig. 92 FOLD FLAT CABLE
1 - RELEASE CABLE
Fig. 93 REMOVE FOLD FLAT HANDLE
1 - PRY TAB INWARD
2 - TRIM TOOL
Fig. 94 REMOVE LOAD FLOOR PANEL
1 - TRIM TOOL
2 - LOAD FLOOR PANEL
CS
SEATS
23 - 149
THIRD ROW OUTBOARD LATCH ASSEMBLY (Continued)
(8) Remove inboard pivot drive shield screw (Fig.
95).
(9) Disengage J-straps to uncover inboard pivot
(Fig. 96).
(10) Remove two bolts attaching inboard free pivot
to inner seat back. Remove two nuts attaching
inboard free pivot to inboard riser
(11) Remove inboard free pivot assembly.
INSTALLATION
(1) Place inboard free pivot assembly into position
(Fig. 92).
(2) Install two bolts attaching inboard free pivot to
inner seat back. Install two nuts attaching inboard
free pivot to inboard riser.
(3) Engage seat cover J-straps.
(4) Install inboard pivot drive shield (Fig. 93).
(5) Align load floor panel and push pins fasteners
with holes in seat frame and press into position (Fig.
92).
(6) Connect fold flat cable to handle and press
handle into position on load floor panel.
(7) Install third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - INSTALLATION).
(8) Install rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE TRAY -
INSTALLATION).
THIRD ROW OUTBOARD
LINK/SHIELD
REMOVAL
(1) Open liftgate.
(2) Remove rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE BIN -
REMOVAL).
(3) Remove third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - REMOVAL).
(4) Remove two bolts (on outboard side of seat)
attaching drive link assembly (Fig. 97).
(5) Remove drive link and shield assembly.
INSTALLATION
(1) Place drive link/shield assembly into position.
(2) Install two bolts (on outboard side of seat)
attaching drive link assembly (Fig. 58). Tighten to 10
N·m (7 ft. lbs.) torque.
(3) Install third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - INSTALLATION).
(4) Install rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE TRAY -
INSTALLATION).
(5) Close liftgate.
Fig. 95 INBOARD PIVOT DRIVE SHIELD
1 - SHIELD
Fig. 96 FREE PIVOT ASSEMBLY
1 - INBOARD FREE PIVOT
Fig. 97 DRIVE LINK AND SHIELD
1 - DRIVE LINK AND SHIELD
23 - 150
SEATS
CS
THIRD ROW INBOARD PIVOT (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст