Chrysler Pacifica. Manual — part 836
(5) Release tab attaching fold flat handle to load
floor panel (Fig. 54).
(6) Disconnect fold flat cable from handle and
remove handle.
(7) Remove load floor panel by using a trim tool
and lifting up the edges to disengage the push pins
(Fig. 55).
(8) Remove two bolts (on outboard side of seat)
attaching drive link assembly (Fig. 56).
(9) Remove drive link assembly.
(10) Remove outboard seat back shield.
(11) Remove one screw (on inboard side of seat)
attaching inboard shield.
(12) Remove inboard shield.
(13) Remove two bolts attaching outer seat back to
outboard latch assembly.
(14) Remove two bolts attaching inner seat back to
inboard free pivot assembly.
(15) Disengage J-straps (Fig. 57).
(16) Remove seat back cover and foam pad from
the seat back frame.
(17) Remove seat back cover from foam pad.
INSTALLATION
(1) Place seat back cover onto cushion.
(2) Install seat back cover and cushion to seat
back frame.
(3) Engage J-straps (Fig. 57).
Fig. 54 REMOVE FOLD FLAT HANDLE
1 - PRY TAB INWARD
2 - TRIM TOOL
Fig. 55 REMOVE LOAD FLOOR PANEL
1 - TRIM TOOL
2 - LOAD FLOOR PANEL
Fig. 56 DRIVE LINK AND SHIELD
1 - DRIVE LINK AND SHIELD
Fig. 57 SEAT BACK - THIRD ROW
1 - THIRD ROW SEAT BACK
2 - J-STRAPS
3 - SEAT BACK FOAM
CS
SEATS
23 - 139
THIRD ROW SEAT BACK CUSHION FOAM/ COVER (Continued)
(4) Install two bolts attaching inner seat back to
inboard free pivot assembly. Tighten to 48 N·m (35 ft.
lbs.) torque.
(5) Install two bolts attaching outer seat back to
outboard fold flat mechanism. Tighten to 48 N·m (35
ft. lbs.) torque.
(6) Install outboard seat back shield.
(7) Install one screw attaching inboard shield.
(8) Install two bolts attaching drive link assembly.
Tighten to 10 N·m (7 ft. lbs.) torque.
(9) Align load floor panel and push pins fasteners
with holes in seat frame and press into position.
(10) Connect fold flat cable to handle and press
handle into position on load floor panel.
(11) Install third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - INSTALLATION).
(12) Install rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE TRAY -
INSTALLATION).
THIRD ROW SEAT CUSHION /
COVER
REMOVAL
(1) Open liftgate.
(2) Remove rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE BIN -
REMOVAL).
(3) Remove third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - REMOVAL).
(4) Remove two bolts (on outboard side of seat)
attaching drive link assembly (Fig. 58).
(5) Remove drive link assembly.
(6) Remove two bolts attaching front cushion pan
to link and riser assemblies (Fig. 59).
(7) Remove cushion assembly by sliding the front
links off of the riser pins and twisting the cushion
assembly to disengage the rear sliders from the riser
tracks (Fig. 60).
(8) Disengage J-straps.
(9) Remove seat cushion cover and foam pad from
the seat pan (Fig. 62) and (Fig. 63).
(10) Remove seat cushion cover from foam pad.
INSTALLATION
(1) Place seat cushion cover onto cushion foam pad
(Fig. 64).
(2) Install seat cushion cover and foam pad seat
pan (Fig. 63).
(3) Engage J-straps (Fig. 62) and (Fig. 61).
(4) Install cushion assembly onto the seat risers.
Fig. 58 DRIVE LINK AND SHIELD
1 - DRIVE LINK AND SHIELD
Fig. 59 THIRD ROW SEAT PAN
1 - J-STRAP
2 - SEAT PAN
3 - FRONT LINK ASSEMBLY
Fig. 60 THIRD ROW SEAT SLIDER
1 - SLIDER
23 - 140
SEATS
CS
THIRD ROW SEAT BACK CUSHION FOAM/ COVER (Continued)
(5) Install cushion assembly by sliding the front
links onto the riser pins and twisting the cushion
assembly to engage the rear sliders onto the riser
tracks (Fig. 60).
(6) Install two bolts attaching front cushion pan to
link and risers (Fig. 59). Tighten to 29 N·m (21 ft.
lbs.) torque.
(7) Install drive link assembly.
(8) Install two bolts attaching drive link assembly
(Fig. 58). Tighten to 10 N·m (7 ft. lbs.) torque.
(9) Install third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - INSTALLATION).
(10) Install rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE TRAY -
INSTALLATION).
(11) Close liftgate.
Fig. 61 THIRD ROW SEAT CUSHION COVER AND
PAN
1 - J-STRAPS
2 - SEAT CUSHION COVER
Fig. 62 THIRD ROW SEAT CUSHION
1 - SEAT CUSHION PAN
2 - SEAT CUSHION FOAM AND COVER
3 - J-STRAPS
Fig. 63 THIRD ROW SEAT CUSHION FOAM PAD
1 - SEAT CUSHION COVER
2 - SEAT CUSHION FOAM PAD
Fig. 64 THIRD ROW SEAT CUSHION COVER
1 - SEAT CUSHION COVER
2 - SEAT CUSHION FOAM PAD
3 - HOOK AND LOOP FASTENER
CS
SEATS
23 - 141
THIRD ROW SEAT CUSHION / COVER (Continued)
THIRD ROW FOLD FLAT
HANDLE
REMOVAL
(1) Open liftgate.
(2) Using finger, disengage fold flat cable from
handle (Fig. 65).
(3) Release tab attaching fold flat handle to load
floor panel (Fig. 66).
(4) Disconnect fold flat cable from handle and
remove handle from load floor panel.
INSTALLATION
(1) Connect fold flat cable to handle (Fig. 53).
(2) Place handle into position on load floor panel
(Fig. 67).
(3) Depress tab and press handle into seated posi-
tion.
THIRD ROW FOLD FLAT
HANDLE AND CABLE
REMOVAL
(1) Open liftgate.
(2) Remove rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE BIN -
REMOVAL).
(3) Remove third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - REMOVAL).
(4) Using finger, disengage fold flat cable from
handle (Fig. 68).
NOTE: Use care not to stretch or kink cable.
Fig. 65 FOLD FLAT CABLE
1 - RELEASE CABLE
Fig. 66 REMOVE FOLD FLAT HANDLE
1 - PRY TAB INWARD
2 - TRIM TOOL
Fig. 67 INSTALL FOLD FLAT HANDLE
1 - DEPRESS TAB
Fig. 68 FOLD FLAT CABLE
1 - RELEASE CABLE
23 - 142
SEATS
CS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст