Chrysler Pacifica. Manual — part 825
FLOOR CONSOLE BASE
ASSEMBLY
REMOVAL
(1) Remove front and rear floor consoles. (Refer to
23
-
BODY/INTERIOR/FLOOR
CONSOLE
-
REMOVAL) and (Refer to 23 - BODY/INTERIOR/
FLOOR CONSOLE - REMOVAL).
(2) Remove
shift
mechanism.
(Refer
to
21
-
TRANSMISSION/TRANSAXLE/AUTOMATIC
-
41TE/SHIFT MECHANISM - REMOVAL).
(3) Remove nine attaching nuts and washers to
weld studs (Fig. 15).
(4) Remove two screws attaching L-brackets to
instrument panel.
(5) Disconnect wire connectors that are still con-
nected.
(6) Raise floor console base assembly to allow wire
harness exit through console base.
(7) Remove floor console base assembly from vehi-
cle.
INSTALLATION
(1) Place floor console base assembly into position
(Fig. 15).
(2) Install wire harnesses through console base
into position.
(3) Connect wire connectors.
(4) Install two screws attaching L-brackets to
instrument panel.
(5) Install nine attaching nuts and washers to
weld studs.
(6) Install shift mechanism. (Refer to 21 - TRANS-
MISSION/TRANSAXLE/AUTOMATIC - 41TE/SHIFT
MECHANISM - INSTALLATION).
(7) Install front and rear floor consoles. (Refer to
23 - BODY/INTERIOR/FLOOR CONSOLE - INSTAL-
LATION) and (Refer to 23 - BODY/INTERIOR/
FLOOR CONSOLE - INSTALLATION).
Fig. 15 FRONT FLOOR CONSOLE BASE ASSEMBLY (BLOWER HOUSING)
1 - INSTRUMENT PANEL
2 - ATTACHING L-BRACKETS
3 - ATTACHING NUTS
4 - ATTACHING SCREWS
5 - FRONT FLOOR CONSOLE BASE ASSEMBLY AND BLOWER
HOUSING
6 - WIRE CONNECTOR
7 - TELEMATICS COMMUNICATION UNIT
8 - FLOOR PAN
9 - FLOOR PAN STUDS
10 - FLOOR CONSOLE STUFFER
CS
INTERIOR
23 - 95
FRONT DOOR SILL SCUFF
PLATE
REMOVAL
(1) Using trim stick (C-4755), disengage push pins
attaching door sill plate to door sill.
(2) Remove door sill scuff plate from vehicle (Fig.
16).
INSTALLATION
(1) Place sill scuff plate in position on vehicle (Fig.
16).
(2) Press sill scuff plate down to engage push pins
to door sill.
HEADLINER
REMOVAL
(1) Disconnect and isolate the negative battery
cable.
(2) Remove sun visors and vanity mirrors.
(3) Remove sun visor center supports.
(4) Remove assist handles attaching screws and
remove, if equipped.
(5) Remove second row dome lamp and coat hook
attaching screw and remove, if equipped.
(6) Remove A-pillar trim. (Refer to 23 - BODY/IN-
TERIOR/A-PILLAR TRIM - REMOVAL).
(7) Remove B-pillar upper trim. (Refer to 23 -
BODY/INTERIOR/B-PILLAR
UPPER
TRIM
-
REMOVAL).
(8) Remove liftgate header trim. (Refer to 23 -
BODY/INTERIOR/REAR
HEADER
TRIM
-
REMOVAL).
(9) Remove D-pillar trim. (Refer to 23 - BODY/IN-
TERIOR/D-PILLAR TRIM - REMOVAL).
(10) Remove C-pillar upper trim, as necessary.
(Refer to 23 - BODY/INTERIOR/C-PILLAR TRIM -
REMOVAL)
(11) Remove overhead console, if equipped. (Refer
to
8
-
ELECTRICAL/OVERHEAD
CONSOLE
-
REMOVAL).
(12) Remove
overhead
DVD
video
screen,
if
equipped. (Refer to 8 - ELECTRICAL/AUDIO/VIDEO
SCREEN - REMOVAL).
(13) Disconnect wire harness connectors at the left
A-pillar (Fig. 17).
(14) Disconnect wire harness connector and wire
clips at the right A-pillar (Fig. 18).
(15) Disconnect rear view mirror wire connector
from mirror.
(16) Disengage push in fasteners attaching head-
lining to roof panel (Fig. 19) and (Fig. 20).
(17) Remove headlining from roof.
(18) Remove headlining through liftgate opening.
INSTALLATION
(1) If installing DVD video screen bracket (Fig.
21).
(a) Install u-nuts into roof bows.
(b) Place bracket into position.
(c) Install attaching screws and washers and
push pins.
Fig. 16 FRONT DOOR SILL SCUFF PLATE
1 - FRONT DOOR SILL
2 - FRONT DOOR SILL SCUFF PLATE
3 - PUSH PIN
Fig. 17 DOME WIRE HARNESS
1 - A-PILLAR
2 - WIRING HARNESS - DOME LAMPS
3 - DOME WIRE HARNESS
4 - BODY WIRE HARNESS
23 - 96
INTERIOR
CS
(2) Place headlining into vehicle through liftgate
opening.
(3) Raise headlining into position.
(4) Engage push in fasteners attaching headlining
to roof panel (Fig. 19) and (Fig. 20).
(5) Disconnect rear view mirror wire connector
from mirror.
Fig. 19 HEADLINER RETAINER BRACKET
1 - WINDSHIELD OPENING UPPER FRAME
2 - ROOF PANEL
3 - GAS GUIDE (SIDE AIRBAG)
4 - HEADLINER ASSEMBLY
5 - ASSIST HANDLE ANCHOR
6 - PUSH PIN(S)
7 - HEADLINER RETAINER BRACKET
Fig. 18 DVD WIRE HARNESS
1 - A-PILLAR
2 - WIRE HARNESS - DVD
3 - WIRING CLIP(S)
4 - ANTENNA CABLE
Fig. 20 HEADLINER ASSEMBLY
1 - ROOF PANEL
2 - HEADLINER ASSEMBLY
3 - PUSH PIN FASTENER
4 - REAR VIEW MIRROR CONNECTOR
CS
INTERIOR
23 - 97
HEADLINER (Continued)
(6) Connect wire harness connector and wire clips
at the right A-pillar (Fig. 18).
(7) Connect wire harness connectors at the left
A-pillar (Fig. 17).
(8) Install overhead DVD video screen, if equipped.
(Refer to 8 - ELECTRICAL/AUDIO/CD CHANGER -
INSTALLATION).
(9) Install overhead console, if equipped. (Refer to
8 - ELECTRICAL/OVERHEAD CONSOLE - INSTAL-
LATION).
(10) Install C-pillar upper trim. (Refer to 23 -
BODY/INTERIOR/C-PILLAR TRIM - REMOVAL)
(11) Install D-pillar trim. (Refer to 23 - BODY/IN-
TERIOR/D-PILLAR TRIM - INSTALLATION).
(12) Install liftgate header trim. (Refer to 23 -
BODY/INTERIOR/REAR HEADER TRIM - INSTAL-
LATION).
(13) Install B-pillar upper trim. (Refer to 23 -
BODY/INTERIOR/B-PILLAR
UPPER
TRIM
-
INSTALLATION).
(14) Install A-pillar trim. (Refer to 23 - BODY/IN-
TERIOR/A-PILLAR TRIM - INSTALLATION).
(15) Install second row dome lamp and coat hook
attaching screws, if equipped.
(16) Install assist handles attaching screws, if
equipped.
(17) Install sun visor center supports.
(18) Install sun visors and vanity mirrors.
(19) Connect negative battery cable.
Fig. 21 VIDEO SCREEN MOUNTING BRACKET
1 - ROOF PANEL
2 - ROOF BOW NUMBER ONE
3 - VIDEO SCREEN BRACKET
4 - U-NUT(S)
5 - ROOF BOW NUMBER TWO
6 - PUSH PIN FASTENER
7 - FOAM TAPE
8 - HEADLINE ASSEMBLY
9 - VIDEO SCREEN
10 - WASHER AND NUT(S)
11 - VIDEO DISPLAY CABLE
12 - WASHER AND SCREW(S)
13 - STUD COLLAR FOR VIDEO DISPLAY
23 - 98
INTERIOR
CS
HEADLINER (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст