Chrysler Pacifica. Manual — part 230
Symptom:
PASSENGER MIRROR COMMON OUTPUT SHORT TO GROUND -
PDM
When Monitored and Set Condition:
PASSENGER MIRROR COMMON OUTPUT SHORT TO GROUND - PDM
When Monitored:
Whenever mirror is idle.
Set Condition:
Driver circuit is shorted to ground.
POSSIBLE CAUSES
DTC PRESENT
POWER MIRROR
PASSENGER MIRROR COMMON DRIVER SHORTED TO GROUND
PASSENGER DOOR MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase DTCs.
Cycle the ignition switch Off then back On.
With the DRBIII
t, read DTCs.
Did the same DTC return?
All
Yes
→ Go To 2
No
→ The conditions required to set the code are currently not present.
Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the power mirror connector.
Turn the ignition on.
Using the DRBIII
t, erase DTC’s.
Cycle the ignition switch Off then back On.
With the DRBIII
t, read DTC’s.
Did the same DTC return?
All
Yes
→ Go To 3
No
→ Inspect the power mirror harness for a short, if OK replace the
mirror.
Perform BODY VERIFICATION TEST - VER 1.
917
POWER MIRROR
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Power Mirror connector.
Turn the ignition on.
Measure the Passenger Mirror Common Driver circuit to ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Passenger Mirror Common Driver circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Passenger Door Module.
Perform BODY VERIFICATION TEST - VER 1.
918
POWER MIRROR
PASSENGER MIRROR COMMON OUTPUT SHORT TO GROUND - PDM —
Continued
Symptom:
PASSENGER MIRROR HORIZONTAL OUTPUT SHORT TO BAT-
TERY - PDM
When Monitored and Set Condition:
PASSENGER MIRROR HORIZONTAL OUTPUT SHORT TO BATTERY - PDM
When Monitored:
Whenever mirror is idle.
Set Condition:
Driver circuit is shorted to battery.
POSSIBLE CAUSES
DTC PRESENT
POWER MIRROR
PASSENGER MIRROR HORIZONTAL DRIVER SHORTED TO VOLTAGE
PASSENGER DOOR MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase DTCs.
Cycle the ignition switch Off then back On.
With the DRBIII
t, read DTCs.
Did the same DTC return?
All
Yes
→ Go To 2
No
→ The conditions required to set the code are currently not present.
Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the power mirror connector.
Using the DRBIII
t, erase DTC’s.
Turn the ignition on.
Cycle the ignition switch Off then back On.
With the DRBIII
t, read DTC’s.
Did the same DTC return?
All
Yes
→ Go To 3
No
→ Inspect the power mirror harness for a short, if OK replace the
mirror.
Perform BODY VERIFICATION TEST - VER 1.
919
POWER MIRROR
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Power Mirror connector.
Turn the ignition on.
Measure the voltage of the Passenger Mirror Horizontal Driver circuit.
Is the voltage above 1.0 volts?
All
Yes
→ Repair the Passenger Mirror Horizontal Driver circuit for a short
to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Passenger Door Module.
Perform BODY VERIFICATION TEST - VER 1.
920
POWER MIRROR
PASSENGER MIRROR HORIZONTAL OUTPUT SHORT TO BATTERY -
PDM —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст