Chrysler Pacifica. Manual — part 835
(21) Remove four seat cushion pan nuts (Fig. 46).
(22) Remove seat cushion pan.
(23) Remove two bolts and five nuts attaching
lower recliner bracket to riser and leg assembly (Fig.
47).
(24) Remove
seat
back
frame/recliners/CRAS
bracket and torque rod.
INSTALLATION
(1) Place seat back frame/recliners/CRAS bracket
and torque rod in position on riser and leg assembly.
(2) Install two bolts and five nuts attaching lower
recliner bracket to riser and leg assembly (Fig. 47).
Tighten nuts to 48 N·m (35 ft. lbs.) torque, and
tighten bolts to 29 N·m (35 ft. lbs.) torque.
(3) Place seat cushion pan into position.
(4) Install four seat cushion pan nuts (Fig. 46).
(5) Place seat cushion foam and cover in position
on seat pan (Fig. 45).
(6) Connect the J-strap and install push pin fas-
teners at the rear of seat cushion pan (Fig. 43) and
(Fig. 44).
(7) Route to under side of cushion pad and connect
heat seat wire harness and three attachments.
NOTE: Use care not to damage wire harness during
install procedure.
(8) Install upper recliner bolts to seat back frame,
and tighten bolts to 48 N·m (35 ft. lbs.) torque (Fig.
41) and (Fig. 42).
(9) Place seat foam/cover in position and work the
foam and cover under recliner torque rod (Fig. 39)
and (Fig. 40).
(10) Feed seat back harness through hole in
shield. Connect wiring harness (for heated seats) at
inner shield and feed back harness through hole in
shield (Fig. 38).
(11) Engage inner J-straps (Fig. 37).
(12) Install trim ring (Fig. 36).
(13) Install screws attaching trim ring to seat back
frame (Fig. 35) and (Fig. 36).
(14) Engage outer J-straps at seat back (Fig. 34).
(15) Install three screws attaching outboard side
shield.
(16) Install two screws attaching inboard side
shield.
(17) Press outboard side handle on retainer tab till
it engages.
(18) Install two screws attaching outer side shield
buckle side.
(19) Install seat inner panel. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT INNER PANEL -
INSTALLATION)
(20) Install armrest. (Refer to 23 - BODY/SEATS/
SEAT ARMREST - INSTALLATION).
(21) Connect heat element wire harness.
(22) Install second row seat. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT - INSTALLATION).
(23) Install headrest and sleeves (Refer to 23 -
BODY/SEATS/HEADREST - INSTALLATION).
(24) Connect battery negative cable.
SECOND ROW SEAT CUSHION
FOAM/COVER
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove headrest. (Refer to 23 - BODY/SEATS/
HEADREST - REMOVAL).
Fig. 46 SEAT CUSHION PAN
1 - ATTACHING NUTS
Fig. 47 SECOND ROW BACK FRAME/RECLINER/
CRAS BRACKET, AND TORQUE ROD
1 - ATTACHING NUTS AND BOLTS
2 - LOWER RECLINER ASSEMBLY
CS
SEATS
23 - 135
SECOND ROW SEAT BACK FRAME/RECLINER/TORQUE ROD/CRAS ASSEMBLY (Continued)
(3) Remove second row seat. (Refer to 23 - BODY/
SEATS/FIRST ROW SEAT - REMOVAL).
(4) Disconnect heat element wire harness.
(5) Remove two screws attaching outer side shield
buckle side.
(6) Remove screw attaching floor dump release
handle and remove handle.
(7) Remove front recliner handle (snaps on).
(8) Remove three screws attaching side shield at
recliner handle side.
(9) Remove three screws attaching inner side
shield hinge area.
(10) Remove hinge to floor plastic cover.
(11) Remove four screws attaching lower plastic
cover, under side of seat.
(12) Disengage J-straps and push pins at cushion
cover (Fig. 48).
(13) Remove cushion and cover from seat pan.
(14) Remove cover from cushion.
INSTALLATION
(1) Place cover on cushion (Fig. 48).
(2) Install cushion and cover to seat pan.
(3) Engage J-straps and push pins to seat pan.
(4) Install four screws attaching lower plastic
cover, to under side of seat.
(5) Install hinge to floor plastic cover.
(6) Install three screws attaching inner side shield
hinge area.
(7) Install three screws attaching side shield at
recliner handle side.
(8) Push on front recliner handle to lock into posi-
tion.
(9) Install screw attaching floor dump release han-
dle.
(10) Install two screws attaching outer side shield
buckle side.
(11) Connect heat element wire harness.
(12) Install first row seat. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT - INSTALLATION).
(13) Install headrest. (Refer to 23 - BODY/SEATS/
HEADREST - INSTALLATION).
(14) Connect battery negative cable.
SECOND ROW SEAT RISER
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove headrest. (Refer to 23 - BODY/SEATS/
HEADREST - REMOVAL).
(3) Remove second row seat. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT - REMOVAL).
(4) Disconnect heat element wire harness.
(5) Turn seat over (Fig. 49).
(6) Remove four nuts attaching seat base to seat
assembly.
(7) Remove seat base.
INSTALLATION
(1) Place seat base into position on second seat
assembly.
(2) Install four nuts attaching seat base to seat
assembly (Fig. 49).
(3) Place seat into position.
(4) Connect heating element wire harness.
Fig. 48 SEAT BACK CUSHION
1 - SECOND ROW SEAT CUSHION COVER
2 - SECOND ROW SEAT CUSHION
3 - SEAT HEATING ELEMENT WIRE HARNESS
4 - SEAT HEATING ELEMENT
Fig. 49 SEAT RAISER
1 - SEAT BASE
2 - SECOND ROW SEAT ASSEMBLY
23 - 136
SEATS
CS
SECOND ROW SEAT CUSHION FOAM/COVER (Continued)
(5) Install second row seat. (Refer to 23 - BODY/
SEATS/SECOND ROW SEAT - INSTALLATION).
(6) Install headrest. (Refer to 23 - BODY/SEATS/
HEADREST - INSTALLATION).
(7) Disconnect and isolate the battery negative
cable.
SECOND ROW SEAT SIDE
SHIELD
REMOVAL
(1) Fold seat flat and tilt seat forward to access
screw.
(2) Remove screw attaching second row seat side
shield (Fig. 50).
(3) Remove side shield.
INSTALLATION
(1) Place side shield into position.
(2) Install screw attaching second row seat side
shield (Fig. 50).
THIRD ROW SEAT
REMOVAL
(1) Open liftgate.
(2) Remove rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE BIN -
REMOVAL).
(3) Remove third row seat rear two attaching bolts
(Fig. 51).
(4) Remove third row seat front covers. (Fig. 52).
(5) Remove the third row seat front two attaching
bolts.
(6) Remove seat from vehicle.
Fig. 50 SEAT CUSHION SIDE SHIELD
1 - SECOND ROW SEAT SIDE SHIELD
2 - ATTACHING SCREW
Fig. 51 THIRD ROW SEAT - REAR SCREWS
1 - THIRD ROW SEAT BACK
2 - REAR ATTACHING BOLTS
3 - REAR FLOOR STOWAGE BIN
CS
SEATS
23 - 137
SECOND ROW SEAT RISER (Continued)
INSTALLATION
(1) Place seat into position in vehicle.
(2) Install third row seat front two attaching bolts
and tighten to 88 N·m (65 ft. lbs.) torque (Fig. 52).
(3) Install third row seat front covers.
(4) Install third row seat two rear attaching bolts
and tighten to 88 N·m (65 ft. lbs.) torque (Fig. 51).
(5) Install rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE BIN -
INSTALLATION).
THIRD ROW SEAT BACK
CUSHION FOAM/ COVER
REMOVAL
(1) Open liftgate.
(2) Remove rear floor stowage bin. (Refer to 23 -
BODY/INTERIOR/REAR FLOOR STOWAGE BIN -
REMOVAL).
(3) Remove third row seat. (Refer to 23 - BODY/
SEATS/THIRD ROW SEAT - REMOVAL).
(4) Using finger, disengage fold flat cable from
handle (Fig. 53).
Fig. 52 THIRD ROW SEATS
1 - ATTACHING WASHERS AND BOLTS
2 - THIRD ROW BUCKET SEATS
3 - FLOOR PAN
4 - CARPETING
5 - THIRD ROW SEAT FRONT COVER
Fig. 53 FOLD FLAT CABLE
1 - RELEASE CABLE
23 - 138
SEATS
CS
THIRD ROW SEAT (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст