Chrysler Pacifica. Manual — part 808
(8) Move top of trim panel away from door, while
supporting bottom trim panel. (Fig. 25).
(9) Disconnect inside handle cable end from clip,
and pull conduit end out from bracket (Fig. 26).
(10) Disconnect
lock
knob
conduit
end
from
bracket. Slide cable barrel end out from the lock
knob and guide cable through slot. Ensure that lock
knob cable did not get bent (Fig. 26).
(11) Disconnect wire connector from power door
lock switch, mirror switch, power window switch, and
courtesy lamp.
(12) Remove trim panel from door.
INSTALLATION
(1) Place trim panel in position.
(2) Move trim panel away from door, and connect
wire connectors to power door lock switch, mirror
switch, and power window switch, and courtesy lamp
(Fig. 25).
CAUTION: Do not allow door trim panel to hang by
the wire connector or wiring.
(3) Slide cable barrel end into lock knob and guide
cable through slot (Fig. 26). Connect lock knob con-
duit end to bracket. Ensure that lock knob cable did
not get kinked.
(4) Connect conduit end into bracket and connect
inside handle cable end into clip. Snap the clip on to
cable end in to clip. Snap the clip on to the cable end.
(5) Connect trim panel to retainer channel in inner
belt weatherstrip at top of door gently jiggling while
lowering into position.
Fig. 24 DOOR TRIM PANEL
1 - PULL HANDLE ATTACHING SCREW
2 - ENSURE MECHANICAL, ELECTRICAL AND LOCK CLIP ARE
THROUGH THE INNER PANEL
3- TRIM ATTACHING SCREW
4 - TOP EDGE OF DOOR TRIM PANEL
5 - DOOR TRIM PANEL
6 - TRIM PANEL LOCATORS
Fig. 25 DISCONNECT DOOR TRIM PANEL
1 - LATCH LOCK KNOB CABLE
2 - LATCH INSIDE HANDLE CABLE
3 - SPEAKER TWEETER
4 - DOOR TRIM PANEL
5 - POWER WINDOW SWITCH CONNECTOR
6 - POWER LOCK SWITCH CONNECTOR
7 - DOOR WIRE HARNESS
CS
DOOR - FRONT
23 - 27
TRIM PANEL (Continued)
(6) Tilt trim panel outward to align locator pins
into position on backside of trim panel.
(7) Applying hand pressure engage push pin fas-
teners attaching trim panel to door around perimeter
of trim panel (Fig. 24).
(8) Install screw behind inside remote handle and
close remote handle trim plug (Fig. 23).
(9) Install screw inside arm rest pull cup and close
remote handle trim plug (Fig. 22).
(10) Raise door glass.
(11) Close door.
WATERSHIELD
REMOVAL
(1) Remove door trim panel. (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - REMOVAL).
NOTE: Care must be taken when routing electrical
wiring & cables through access holes to prevent
tearing of liner material.
(2) Route wiring bundle for power locks, switch
bezel, window switch, and memory switch (left door
only).
(3) Pull courtesy light wiring through watershield.
(4) Peel watershield away from adhesive around
perimeter of inner door panel (Fig. 27).
(5) Remove watershield.
INSTALLATION
(1) Place watershield into position (Fig. 27).
NOTE: Care must be taken when routing electrical
wiring & cables through access holes to prevent
tearing of liner material.
(2) Pull latch cable, through watershield.
(3) Pull courtesy light wiring, through watershield.
Fig. 26 FRONT DOOR TRIM PANEL MECHANICAL CONNECTIONS
1 - LOCK KNOB CABLE CONDUIT END
2 - LOCK KNOB CABLE BARREL END
3 - DOOR TRIM PANEL
4 - CABLE BRACKET
5 - REMOTE HANDLE CABLE END
6 - REMOTE HANDLE CABLE CONDUIT END
Fig. 27 DOOR WATERSHIELD
1 - DOOR ASSEMBLY
2 - WATERSHIELD
23 - 28
DOOR - FRONT
CS
TRIM PANEL (Continued)
(4) Route wiring bundle for power locks, switch
bezel, window switch, and memory switch (left door
only) through watershield.
(5) Insure
that
enough
adhesive
remains
to
securely retain the watershield to inner door panel.
Replace as necessary.
(6) Install door trim panel. (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - INSTALLATION).
WINDOW REGULATOR
REMOVAL
(1) Remove door trim panel. (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - REMOVAL).
(2) Remove watershield. (Refer to 23 - BODY/
DOOR - FRONT/WATERSHIELD - REMOVAL).
(3) Remove inner belt molding. (Refer to 23 -
BODY/WEATHERSTRIP/SEALS/FDR INNER BELT
WEATHERSTRIP - REMOVAL).
(4) Remove door glass. (Refer to 23 - BODY/DOOR
- FRONT/WINDOW - REMOVAL).
(5) Disconnect wire connector from power window
motor (Fig. 28).
(6) Loosen screws attaching front and rear window
guide rails to inner door panel (Fig. 29).
(7) Remove screw heads on guide rails from key
hole slots in inner door panel.
(8) Loosen screws attaching motor/housing to inner
door panel.
(9) Remove regulator from inner door panel.
(10) Extract rear guide rail through inner door
panel rear access hole.
(11) Extract front guide rail through front access
hole (Fig. 30).
INSTALLATION
(1) Insert window regulator through the rear
access hole (Fig. 29).
(2) Place window regulator in position on inner
door panel.
Fig. 28 POWER WINDOW REGULATOR
1 - DOOR WIRE HARNESS
2 - DOOR ASSEMBLY
3 - FRONT DOOR POWER REGULATOR
Fig. 29 POWER WINDOW REGULATOR ASSEMBLY
1 - DOOR ASSEMBLY
2 - FRONT DOOR POWER WINDOW REGULATOR
3 - REGULATOR ATTACHING SCREWS
CS
DOOR - FRONT
23 - 29
WATERSHIELD (Continued)
(3) Place screw heads on guide rails in position
through key hole slots in inner door panel.
(4) Tighten screws to attach front and rear guide
rails to inner door panel to 9 N·m (80 in. lbs.).
(5) Tighten screws to attach motor/housing to
inner door panel to 9 N·m (80 in. lbs.).
(6) Connect wire connector into power window
motor (Fig. 28).
(7) Install door glass. (Refer to 23 - BODY/DOOR -
FRONT/WINDOW - INSTALLATION).
(8) Verify door glass alignment and operation.
(9) Install inner belt molding. (Refer to 23 - BODY/
WEATHERSTRIP/SEALS/FDR
INNER
BELT
WEATHERSTRIP - INSTALLATION).
(10) Install watershield. (Refer to 23 - BODY/
DOOR - FRONT/WATERSHIELD - INSTALLATION).
(11) Install door trim panel. (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - INSTALLATION).
GLASS RUN LOWER CHANNEL
REMOVAL
(1) Remove door trim panel. (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - REMOVAL).
(2) Remove watershield an necessary. (Refer to 23
-
BODY/DOOR
-
FRONT/WATERSHIELD
-
REMOVAL).
(3) Loosen screws attaching door glass run lower
channel to inner door panel (Fig. 31).
(4) Remove door glass run lower channel from
inner door panel.
(5) Extract door glass run lower channel through
front access hole.
INSTALLATION
(1) Place door glass run lower channel through
front access hole into key hole slots (Fig. 31).
(2) Tighten screws attaching door glass run lower
channel to inner door panel to 6 N·m (55 in. lbs.)
torque.
(3) Place watershield into position. (Refer to 23 -
BODY/DOOR - FRONT/WATERSHIELD - INSTAL-
LATION).
(4) Install door trim panel. (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - INSTALLATION).
Fig. 30 FRONT DOOR WINDOW REGULATOR
1 - WINDOW REGULATOR
2 - ELECTRIC MOTOR
Fig. 31 DOOR GLASS RUN LOWER CHANNEL
1 - DOOR ASSEMBLY
2 - GLASS CHANNEL ATTACHING SCREWS
3 - DOOR GLASS RUN LOWER CHANNEL
23 - 30
DOOR - FRONT
CS
WINDOW REGULATOR (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст