Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 1729
32. Shift crossmember as necessary to line up
mounts (3) with location marks drawn on body (1)
before removal.
33. Once mounts are lined up with location marks, on
both sides of vehicle, measure distance (1)
between the tension link (2) and weld flange (3)
on body directly in front of it, just outboard of the
front mount bushing (4). This distance must be
at least 12 mm to allow proper clearance for
suspension movement. If distance is less than
12 mm on either side of vehicle, shift that side of
rear crossmember directly rearward until distance
is 12 mm or greater. To do so, loosen 3 mounting
bolts slightly, leaving one on opposite side of shift
snugged to pivot off of. Shift crossmember rear-
ward and snug loosened bolts. Remeasure oppo-
site side to be sure it still maintains minimum 12
mm distance.
34. Tighten all four crossmember mounting bolts (2
and 3) to 180 N·m (133 ft. lbs.).
13 - 116
FRAME & BUMPERS
LX
35. Remove jack (3) from under rear crossmember.
36. Install fuel filler tube. (Refer to 14 - FUEL SYS-
TEM/FUEL DELIVERY/FUEL TANK FILLER TUBE
- INSTALLATION)
37. Clip left rear wheel speed sensor cable (2) to
routing clip (1) above toe link mount on rear
crossmember.
LX
FRAME & BUMPERS
13 - 117
38. Clip left rear wheel speed sensor cable (1) to
routing clips (2) along rear of crossmember near
rear differential (3).
39. Clip left rear wheel speed sensor cable (3) to
routing clip (1) near body connector.
40. Match left rear wheel speed sensor connector (4)
to right sensor connector (3) to make one connec-
tor.
41. Insert speed sensor connectors (3 and 4) into
body wiring harness connector (1) located in lug-
gage compartment floor pan (2). When installing
connector, make sure retaining clip on body con-
nector is properly in place and sensor connector
cannot be pulled out.
13 - 118
FRAME & BUMPERS
LX
42. If equipped with standard or premium disc brakes,
on each rear disc brake:
a. Push caliper guide pins into caliper adapter to
clear caliper mounting bosses when installing.
b. Guide caliper and brake hose down through
rear suspension, then slide caliper over brake
pads and onto caliper adapter (3).
c.
CAUTION: Extreme caution should be taken not to
cross-thread caliper guide pin bolts (2) when they
are installed.Align caliper mounting holes with
guide pins, then install guide pin bolts (2). While
holding guide pins from turning, tighten bolts to
31 N·m (23 ft. lbs.) torque.
d. Make sure brake hose is properly routed and
will not come in contact with suspension com-
ponents.
43. If equipped with SRT8 disc brakes, at each rear disc brake, support spring link using a transmission jack or
other appropriate jack as indicated in removal procedure. (Refer to 13 - FRAME & BUMPERS/FRAME/REAR
CROSSMEMBER - REMOVAL)
44. If equipped with SRT8 disc brakes, on each rear
disc brake, slide caliper with pads (2) over brake
rotor and align with knuckle.
45. If equipped with SRT8 disc brakes, on each rear
disc brake, install caliper mounting bolts (1).
Tighten bolts to 130 N·m (96 ft. lbs.).
46. If equipped with SRT8 disc brakes, on each rear
disc brake, remove jack from under spring link.
LX
FRAME & BUMPERS
13 - 119
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст