Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2134
7. Reinstall the trim panel onto the inside of the rear door. (Refer to 23 - BODY/DOOR - REAR/TRIM PANEL -
INSTALLATION).
23 - 84
DOOR - REAR
LX
WINDOW REGULATOR
REMOVAL
1. Remove the trim panel from the inside of the rear
door. (Refer to 23 - BODY/DOOR - REAR/TRIM
PANEL - REMOVAL).
2. Remove the watershield from the inside of the rear
door. (Refer to 23 - BODY/DOOR - REAR/WATER-
SHIELD - REMOVAL).
3. Remove the door glass channel and bracket from
the inside of the rear door. (Refer to 23 - BODY/
DOOR
-
REAR/GLASS
RUN
CHANNEL
-
REMOVAL).
4. Remove the screw (2) that secures the bottom of
the pull cup bracket (1) to the inside of the rear
door.
5. Loosen the screw that secures the top of the pull
cup bracket to the inside of the rear door.
6. Disengage the upper pull cup bracket screw from
the keyed hole and remove the bracket from the
inside of the rear door.
7. Using the regulator, adjust the rear door glass (1)
position up or down as required for access to the
two window regulator glass clamps (2).
8. Loosen the screw (3) in each of the glass clamps
far enough to release the glass.
9. Lift the glass out of the regulator clamps and into
its full up position, then tape the glass securely into
place.
LX
DOOR - REAR
23 - 85
10. Remove the screw (1) that secures the top of the
rear regulator rail (2) to the inside of the door.
11. Remove the screw (4) that secures the regulator
motor support bracket to the inside of the door.
12. Loosen the screw that secures the bottom of the
regulator rail to the keyed hole (3) on the inside of
the door.
13. Lift the rear regulator rail upward within the door
far enough to disengage the screw from the
keyed hole in the door.
14. Lower the rear regulator within the door (3) far
enough to access and disconnect the door wire
harness connector (1) from the regulator motor (2)
through the large access hole on the inside of the
door near the front.
15. Remove the regulator through the large access
hole on the inside of the door.
23 - 86
DOOR - REAR
LX
INSTALLATION
1. Load the regulator into the door (3) through the
large access hole on the inside of the door near
the front.
2. Position the rear regulator within the door so that
the door wire harness connector (1) can be recon-
nected to the regulator motor (2) through the large
access hole on the inside of the door.
3. Engage the screw at the bottom of the rear regula-
tor rail (2) into the keyed hole (3) on the inside of
the door near the bottom.
4. Install and tighten the screw (1) that secures the
top of the rear regulator rail to the inside of the
door. Tighten the screw to 10 N·m (90 in. lbs.).
5. Install and tighten the screw (4) that secures the
regulator motor support bracket to the inside of the
door. Tighten the screw to 10 N·m (90 in. lbs.).
6. Tighten the screw that secures the bottom of the
regulator rail to the keyed hole on the inside of the
door. Tighten the screw to 10 N·m (90 in. lbs.).
LX
DOOR - REAR
23 - 87
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст