Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2144
INSTALLATION
1. Position the hood latch release handle and cable
(3) under the left side of the instrument panel in the
passenger compartment of the vehicle.
2. Thread the cable through the appropriate hole in
the dash panel far enough to seat the cable grom-
met (1) into the hole.
3. Position the hood latch release handle to the lower
instrument panel reinforcement (2).
4. Install and tighten the two screws (4) that secure
the handle to the reinforcement. Tighten the screws
to 5 N·m (45 in. lbs.).
5. Reinstall the closeout panel beneath the left side of
the instrument panel. (Refer to 23 - BODY/IN-
STRUMENT
PANEL/INSTRUMENT
PANEL
SILENCER - INSTALLATION).
6. Route the hood latch release cable from the dash
panel along the left side of the engine compartment
to the center of the headlamp mounting crossmem-
ber as shown.
7. Fully engage the cable into the integral routing
clips on the headlamp mounting crossmember and
the routing clips (1) along the left side of the
engine compartment.
8. Reinstall the left headlamp unit to the vehicle.
(Refer to 8 - ELECTRICAL/LAMPS/LIGHTING -
EXTERIOR/HEADLAMP UNIT - INSTALLATION).
9. Reinstall the hood latch (2) to the vehicle. (Refer to
23 - BODY/HOOD/LATCH - INSTALLATION).
23 - 124
HOOD
LX
LATCH STRIKER
REMOVAL
1. Open and support the hood (3).
2. Remove the two screws (2) that secure the latch
striker (1) to the hood inner reinforcement.
3. Remove the striker from the vehicle.
INSTALLATION
1. Position the latch striker (1) to the underside of the
hood (3).
2. Install and tighten the two screws (2) that secure
the striker to the hood inner reinforcement. Tighten
the screws to 28 N·m (21 ft. lbs.).
3. Close the hood.
LX
HOOD
23 - 125
ROD-PROP
REMOVAL
1. Open and support the hood.
2. Remove the blind rivet (1) that secures the hood
prop rod (2) pivot bracket to the right side of the
headlamp mounting crossmember (3).
3. Disengage the prop rod from the rod clip (4) on the
left side of the headlamp mounting crossmember.
4. Remove the hood prop rod from the vehicle.
INSTALLATION
1. Position the hood prop rod (2) pivot bracket to the
right side of the headlamp mounting crossmember
(3).
2. Secure the pivot bracket to the headlamp mounting
crossmember with a new blind rivet (1).
3. Engage the prop rod into the rod clip (4) on the left
side of the headlamp mounting crossmember.
4. Close the hood.
23 - 126
HOOD
LX
SUPPORT CYLINDER
REMOVAL
1. Open and support the hood with a suitable prop or
block.
2. Insert a small flat-bladed tool into the lower notch
of the retainer (1) of the lower ball socket end (2)
of the support cylinder on the top of the fender load
beam and carefully pry the retaining clip upward to
the installation position.
WARNING: To avoid personal injury or death, dur-
ing service lift the ball socket end retaining clip
only far enough to release the socket from the ball
stud. Excessive prying or removal of the clip may
result in improper clip spring tension. Improper
clip tension may result in the support cylinder
separating from the ball stud causing sudden,
unexpected loss of hood support.
3. Insert a small flat-bladed tool (3) into the notch on
the outer face of the upper ball socket end (1) of
the support cylinder and carefully pry the retaining
clip (2) outward while pulling the ball socket away
from the ball stud (4) on the upper hood hinge
bracket.
4. Release the retaining clip to its installed position.
5. Disengage the lower ball socket from the ball stud.
6. Remove the support cylinder from the vehicle.
LX
HOOD
23 - 127
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст