Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2119
INSTALLATION
1. Position the lower bracket of the deck lid hinge (1)
to the drain trough on the vehicle.
2. Install and tighten the three screws (2) that secure
the hinge to the drain trough. Tighten the screws to
28 N·m (21 ft. lbs.).
3. Position the deck lid (1) to the upper hinge bracket
(3) on the vehicle.
4. Install and tighten the two screws (2) that secure
the hinge to the deck lid. Tighten the screws to 28
N·m (21 ft. lbs.).
5. Reinstall the support cylinder onto the deck lid
hinge. (Refer to 23 - BODY/DECKLID/CYLINDER -
DECKLID SUPPORT - INSTALLATION).
6. Remove the fixture being used to support the deck
lid for service and close the deck lid.
7. Adjust the deck lid hinge position as necessary to
achieve proper spacing and operation.
23 - 24
DECKLID
LX
LATCH
REMOVAL
1. Open the deck lid.
2. Disconnect and isolate the battery negative cable.
3. Remove the cover from over the latch on the inside
of the deck lid. (Refer to 23 - BODY/DECKLID/
COVER - DECKLID LATCH - REMOVAL).
4. Disconnect the connector (2) of the body wire har-
ness take out for the deck lid (1) from the latch
connector receptacle (3).
5. Remove the two screws (2) that secure the latch
(3) to the inside of the deck lid (1).
6. Remove the latch from the inside of the deck lid.
LX
DECKLID
23 - 25
INSTALLATION
1. Position the latch (3) to the inside of the deck lid
(1).
2. Install and tighten the two screws (2) that secure
the latch to the inside of the deck lid. Tighten the
screws to 8 N·m (71 in. lbs.).
3. Reconnect the connector (2) of the body wire har-
ness take out for the deck lid (1) to the latch con-
nector receptacle (3).
4. Reinstall the cover over the latch on the inside of
the deck lid. (Refer to 23 - BODY/DECKLID/
COVER - DECKLID LATCH - INSTALLATION).
5. Reconnect the battery negative cable.
6. Close the deck lid.
23 - 26
DECKLID
LX
LATCH STRIKER
REMOVAL
1. Open the deck lid.
2. Remove the trunk rear trim panel from the inside of
the deck opening lower panel (3). (Refer to 23 -
BODY/INTERIOR/TRUNK REAR TRIM PANEL -
REMOVAL).
3. Mark the deck lid latch striker (2) location on the
inside of the deck opening lower panel to aid rein-
stallation.
4. Remove the two screws (1) that secure the latch
striker to the inside of the deck opening lower
panel.
5. Remove the latch striker from the vehicle.
INSTALLATION
1. Position the deck lid latch striker (2) to the inside of
the deck opening lower panel (3).
2. Install and tighten the two screws (1) that secure
the latch striker to the deck opening lower panel.
Tighten the screws to 28 N·m (21 ft. lbs.).
3. Adjust the latch striker position as necessary to
achieve proper deck lid latch operation.
4. Reinstall the trunk rear trim panel to the deck
opening lower panel. (Refer to 23 - BODY/INTERI-
OR/TRUNK REAR TRIM PANEL - INSTALLATION).
5. Close the deck lid.
LX
DECKLID
23 - 27
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст