Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2155
B-PILLAR TRIM
REMOVAL
LOWER
1. Loosen the front door sill portion of the lower cowl
trim at the rear of the front door opening for access
to the forward lower B-pillar trim screw. (Refer to
23 - BODY/INTERIOR/COWL TRIM - REMOVAL).
2. Loosen the front of the scuff plate trim from the
rear door sill for access to the rearward lower B-pil-
lar trim screw. (Refer to 23 - BODY/INTERIOR/
DOOR SILL SCUFF PLATE - REMOVAL).
3. Move aside the seat belt webbing to access and
remove the two screws (2) that secure the upper
end of the lower B-pillar trim (3) to the inside of the
B-pillar (1).
4. Remove the two screws (4) that secure the lower
end of the B-pillar trim to the front and rear door
sills.
5. Disengage the seat belt webbing from the slot in
the upper end of the lower B-pillar trim through the
slit in the trim and remove the trim from the inside
of the B-pillar.
UPPER
1. Remove the lower trim from the inside of the B-pil-
lar (2). (Refer to 23 - BODY/INTERIOR/B-PILLAR
TRIM - REMOVAL).
2. Unsnap and remove the trim cover (3) from the
seat belt turning loop on the inside of the upper
B-pillar.
3. Remove the screw (1) that secures the turning loop
to the seat belt height adjuster on the upper B-pil-
lar.
4. Lower the seat belt (4) and turning loop from the
B-pillar.
23 - 168
INTERIOR
LX
5. Remove the screw (1) that secures the lower end
of the upper trim (4) to the inside of the B-pillar (3).
6. Using a trim stick or another suitable wide flat-
bladed tool, carefully pry the lower end of the
upper B-pillar trim away from the inside of the
B-pillar far enough to disengage the two spring clip
retainers that secure the trim to the slots in the pil-
lar.
7. Lift the lower end of the upper trim upward to dis-
engage the locator tab (2) from the locator hole
and remove the trim from the inside of the B-pillar.
INSTALLATION
LOWER
1. Engage the seat belt webbing through the slit and
into the slot in the upper end of the lower B-pillar
trim (3) and position the trim to the inside of the
B-pillar (1). Be certain the webbing is not twisted.
2. Press fit the lower end of the lower B-pillar trim to
the front and rear door opening sills.
3. Install and tighten the two screws (4) that secure
the lower end of the B-pillar trim to the front and
rear door sills. Tighten the screws to 2 N·m (22 in.
lbs.).
4. Move aside the seat belt webbing to install and
tighten the two screws (2) that secure the upper
end of the lower B-pillar trim to the inside of the
B-pillar. Tighten the screws to 2 N·m (22 in. lbs.).
5. Reinstall the scuff plate trim onto the rear door sill.
(Refer
to
23
-
BODY/INTERIOR/DOOR
SILL
SCUFF PLATE - INSTALLATION).
6. Reinstall the lower cowl trim onto the front door
opening sill. (Refer to 23 - BODY/INTERIOR/
COWL TRIM - INSTALLATION).
LX
INTERIOR
23 - 169
UPPER
1. Engage the locator tab (2) on the back of the upper
trim (4) into the locator hole on the inside of the
B-pillar (3).
2. Align the two spring clip retainers on the trim with
the slots in the inner B-pillar.
3. Using hand pressure, press firmly and evenly on
the trim over each of the spring clip locations until
the retainers snap into place.
4. Install and tighten the screw (1) that secures the
lower end of the upper trim to the inside of the
B-pillar. Tighten the screw to 3 N·m (25 in. lbs.).
5. Position the seat belt (4) and turning loop to the
height adjuster on the upper B-pillar (2). Be certain
that the webbing is not twisted.
6. Install and tighten the screw (1) that secures the
turning loop to the seat belt height adjuster on the
upper B-pillar. Tighten the screw to 40 N·m (30 ft.
lbs.).
7. Position the trim cover (3) over the seat belt turning
loop on the inside of the upper B-pillar.
8. Using hand pressure, press the trim cover and
turning loop together until the cover snaps into
place.
9. Reinstall the lower trim onto the inside of the B-pil-
lar. (Refer to 23 - BODY/INTERIOR/B-PILLAR
TRIM - INSTALLATION).
23 - 170
INTERIOR
LX
C-PILLAR TRIM
REMOVAL
UPPER - SEDAN
1. Remove the rear seat cushion from the vehicle.
(Refer to 23 - BODY/SEATS/SEAT CUSHION
COVER - REMOVAL).
2. Remove the lower trim from the inside of the C-pil-
lar. (Refer to 23 - BODY/INTERIOR/C-PILLAR
TRIM - REMOVAL-LOWER).
3. Remove the screw that secures the outboard rear
seat belt lower anchor to the quarter inner panel.
4. Using a trim stick or another suitable wide flat-
bladed tool, carefully pry the upper edge of the
upper C-pillar trim (3) away from the quarter inner
panel (1) far enough to disengage the upper spring
clip retainers that secure the trim to the slots in the
quarter inner panel and (if equipped) the curtain
airbag support.
5. Rotate the upper edge of the upper C-pillar trim
downward to disengage the locator pin (2) on the
back of the panel from the locator hole in the quar-
ter inner panel.
6. Pull the outboard rear seat belt webbing and lower anchor through the slot in the upper C-pillar trim.
7. Carefully pry the lower edge of the upper C-pillar trim away from the quarter inner panel far enough to disengage
the lower spring clip retainers that secure the trim to the slots in the quarter inner panel and remove the trim
from the vehicle.
LOWER
1. Remove the rear seat cushion from the vehicle.
(Refer to 23 - BODY/SEATS/SEAT CUSHION
COVER - REMOVAL).
2. Remove the rear seat back side bolster from the
quarter inner panel (1). (Refer to 23 - BODY/
SEATS/SEAT
BACK
CUSHION/COVER
-
REMOVAL).
3. Remove the screw (4) that secures the upper end
of the lower C-pillar trim (5) to the rear shelf panel
(3).
4. Remove the two screws that secure the lower
C-pillar trim to the quarter inner panel.
5. Remove the lower C-pillar trim from the quarter
inner panel.
LX
INTERIOR
23 - 171
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст