Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2156
UPPER - WAGON
1. Remove the rear seat cushion from the vehicle.
(Refer to 23 - BODY/SEATS/SEAT CUSHION
COVER - REMOVAL).
2. Loosen the front edge of the quarter trim panel
from the inside of the lower C-pillar. (Refer to 23 -
BODY/INTERIOR/QUARTER
TRIM
PANEL
-
REMOVAL).
3. Remove the screw (3) that secures the lower end
of the upper C-pillar trim (1) to the quarter inner
panel (4).
4. Using a trim stick or another suitable wide flat-
bladed tool, carefully pry the rear edge of the upper
C-pillar trim away from the quarter inner panel far
enough to disengage the upper spring clip retainer
that secures the trim to the slot in the quarter inner
panel.
5. Pull the lower edge of the upper C-pillar trim away
and down to disengage the locator tab (2) on the
back of the panel from the locator hole in the quar-
ter inner panel.
6. Remove the upper C-pillar trim from the vehicle.
INSTALLATION
UPPER - SEDAN
1. If the vehicle is so equipped, be certain that the
curtain airbag support (3) is properly installed and
in good condition on the quarter inner panel (1).
Replace the support if any damage is evident.
Tighten the screws (4) into the spring nuts (2) to 2
N·m (15 in. lbs.).
23 - 172
INTERIOR
LX
2. Align the spring clip retainers on the lower edge of
the upper C-pillar trim (3) with the installation holes
in the quarter inner panel (1) and pull the outboard
rear seat belt webbing and lower anchor through
the slot in the trim.
3. Rotate the top of the upper C-pillar trim upwards
far enough to engage the locating pin (2) into the
locating hole in the quarter inner panel.
4. Align the spring clip retainers on the trim with the
slots in the quarter inner panel and (if equipped)
the curtain airbag support.
5. Using hand pressure, press firmly and evenly on
the trim over each of the spring clip locations until
the retainers snap into place.
6. Reinstall the lower trim onto the inside of the C-pil-
lar. (Refer to 23 - BODY/INTERIOR/C-PILLAR
TRIM - INSTALLATION-LOWER).
7. Position the outboard rear seat belt lower anchor to
the quarter inner panel.
8. Install and tighten the screw that secures the outboard rear seat belt lower anchor to the quarter inner panel.
Tighten the screw to 32 N·m (24 ft. lbs.).
9. Reinstall the rear seat cushion into the vehicle. (Refer to 23 - BODY/SEATS/SEAT CUSHION COVER - INSTAL-
LATION).
LOWER
1. Check to be certain that the spring nuts (2) are
properly installed and in good condition on the
quarter inner panel (1). Replace the spring nut if
any damage is evident.
2. Position the lower C-pillar trim (5) onto the quarter
inner panel with the lower edge sequenced over
the rear extension of the rear door sill scuff plate
(6).
3. Install and tighten the two screws (4) that secure
the lower C-pillar trim to the quarter inner panel.
Tighten the screws to 1 N·m (11 in. lbs.).
4. Install and tighten the screw that secures the lower
C-pillar trim to the rear shelf panel (3). Tighten the
screw to 1 N·m (11 in. lbs.).
5. Reinstall the rear seat back side bolster onto the
quarter inner panel. (Refer to 23 - BODY/SEATS/
SEAT BACK CUSHION/COVER - INSTALLATION).
6. Reinstall the rear seat cushion into the vehicle.
(Refer to 23 - BODY/SEATS/SEAT CUSHION
COVER - INSTALLATION).
LX
INTERIOR
23 - 173
UPPER - WAGON
1. Check to be certain that the spring nut (5) is prop-
erly installed and in good condition on the quarter
inner panel (4). Replace the spring nut if any dam-
age is evident.
2. Position the upper C-pillar trim (1) to the quarter
inner panel in the vehicle.
3. Engage the locator tab (2) on the back of the upper
C-pillar trim into the locator hole in the quarter
inner panel.
4. Align the spring clip retainer on the upper rear cor-
ner of the upper C-pillar trim with the installation
hole in the quarter inner panel.
5. Using hand pressure, press firmly and evenly on
the trim over the spring clip location until the
retainer snaps into place.
6. Install and tighten the screw (3) that secures the
lower end of the upper C-pillar trim to the quarter
inner panel. Tighten the screw to 2 N·m (15 in.
lbs.).
7. Reinstall the front edge of the quarter trim panel onto the inside of the lower C-pillar. (Refer to 23 - BODY/
INTERIOR/QUARTER TRIM PANEL - INSTALLATION).
8. Reinstall the rear seat cushion into the vehicle. (Refer to 23 - BODY/SEATS/SEAT CUSHION COVER - INSTAL-
LATION).
23 - 174
INTERIOR
LX
CARPET
REMOVAL
FRONT
NOTE: The front carpet consists of two individual
carpets, one for the driver side and one for the
passenger side. These carpets can be removed
from and installed into the vehicle individually.
1. Remove the driver and/or passenger front seat
from the vehicle as appropriate. (Refer to 23 -
BODY/SEATS/SEAT-FRONT - REMOVAL).
2. Remove the center console from the front floor
panel transmission tunnel. (Refer to 23 - BODY/IN-
TERIOR/FLOOR CONSOLE - REMOVAL).
3. Remove the trim from the driver or passenger side
lower cowl side inner panel as appropriate. (Refer
to 23 - BODY/INTERIOR/COWL TRIM - REMOV-
AL-LOWER).
4. Remove the two push-pin fasteners (1) that secure
the outboard edge of the front carpet (3) to the
front door opening sill.
5. On the driver side only, remove the push-pin fastener (2) that secures the front carpet to the cowl side inner
panel above the foot rest.
6. On the driver side only, remove the push-pin fas-
tener (3) that secures the inboard edge of the front
carpet (1) to the transmission shifter bracket (2).
7. Remove the front carpet from the floor panel.
LX
INTERIOR
23 - 175
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст