Chrysler New Yorker. Manual — part 324
REAR DOOR LATCH
REMOVAL
(1) Close door glass.
(2) Remove door trim panel.
(3) Remove rear glass channel.
(4) Disconnect lock button link from door latch.
(5) Disconnect outside door handle link from door
latch.
(6) Remove screws attaching door latch to door end
frame (Fig. 81).
(7) Remove latch from door.
INSTALLATION
(1) Place latch in position in door.
(2) Install screws attaching door latch to door end
frame.
(3) Connect outside door handle link to door latch.
(4) Connect lock button link to door latch.
(5) Install rear glass channel.
(6) Verify door latch operation.
(7) Install door trim panel.
REAR DOOR LATCH STRIKER
REMOVAL
(1) Open rear door.
(2) Mark location of door latch striker on C-pillar
to assist installation alignment.
(3) Remove bolts holding striker to C-pillar (Fig.
82).
(4) Remove door latch striker from vehicle.
INSTALLATION
(1) Place door latch striker in position on vehicle.
(2) Install bolts to hold striker to C-pillar.
(3) Align striker to marked location on C-pillar
and tighten bolts.
(4) Verify alignment and operation of door, adjust
as necessary.
Fig. 80 Rear Door Hinge
Fig. 81 Rear Door Latch
300M
BODY
23 - 37
REMOVAL AND INSTALLATION (Continued)
REAR DOOR MOUNTED WEATHERSTRIP
REMOVAL
(1) Open rear door.
(2) Using a fork type prying tool, disengage push
in fasteners attaching weatherstrip to lower door.
(3) Remove body mounted weatherstrip from pinch
weld around door opening (Fig. 83).
INSTALLATION
(1) Place door mount weatherstrip in position on
door with the paint dot in the upper corner of the
B-pillar.
(2) Install
push
in
fasteners
to
attach
door
mounted weatherstrip to lower door.
(3) Verify door alignment and seal.
REAR DOOR SAIL PANEL
REMOVAL
(1) Open the rear door.
(2) Using an trim stick, release clip attaching sail
panel to the door.
(3) Remove sail panel.
INSTALLATION
(1) Position sail panel on door.
(2) Press on sail panel to engage clips.
REAR DOOR TRIM PANEL
REMOVAL
CAUTION:
Do not pry on door trim panel, damage
to trim panel will result.
(1) Remove trim plug from the remote bezel by
inserting a small flat blade tool into the notch and
remove, if equipped (LHS/300M).
(2) Remove screw in the pull cup.
(3) Remove screw in remote bezel.
(4) Remove three screws from the bottom edge of
door (Fig. 84).
(5) Using an trim tool, disengage the retaining
clips from the door trim panel to the door panel. Two
clips at the rear of panel and one at the front of the
panel (Fig. 85).
(6) Raise trim panel up over the door flange and
being careful to hold the panel securely.
(7) Disconnect the remote linkage from the door
remote handle.
(8) Remove the wire connect from the rear door
speaker.
(9) Disconnect power window switch wire connector.
(10) Disconnect wiring harness clips from the trim
panel.
(11) Disconnect the courtesy lamp.
(12) Remove trim panel from door.
INSTALLATION
(1) Place trim panel in position on door.
(2) Connect the courtesy lamp.
(3) Connect the wiring harness clips to the trim
panel.
(4) Connect the power window switch wire harness
connector.
(5) Connect the rear door speaker wire connect.
(6) Connect the remote handle linkage.
(7) Install the water shield. Ensure that the water
shield locator holes align. Ensure that the shield is
sealed.
Fig. 82 Rear Door Latch Striker
Fig. 83 Rear Door Mounted Weatherstrip
23 - 38
BODY
300M
REMOVAL AND INSTALLATION (Continued)
(8) Place trim panel into channel retainer at top
door.
(9) Insert trim panel into channel retainer at top
door.
(10) Insert the forward four way alignment guide
into position. Insert the rearward two way alignment
guide into position.
(11) Install new retaining clips to attach door trim
panel to door panel.
(12) Engage retaining clips attach door trim panel
to door panel.
(13) Install three screws to the bottom of the door.
Tighten screws 1.7 to 2.3 N·m (15 to 20 in. lbs.)
torque.
(14) Install screw in the remote bezel.
(15) Install screw in pull cup. Tighten screw 1.7 to
2.3 N·m (15 to 20 in. lbs.) torque.
(16) Install remote bezel trim plug, if equipped.
REAR SEAT ARM REST – 60/40
REMOVAL
(1) Open door.
(2) Fold down 40 rear seat.
(3) Remove arm rest bolt (Fig. 86).
(4) Remove retaining C-clip.
(5) Remove arm rest.
INSTALLATION
(1) Place arm rest on bracket.
(2) Install arm rest nut. Tighten to 12 N·m (9 ft.
lbs.) torque.
(3) Install access retaining nut cover.
(4) Reposition the seats.
REAR SEAT ARM REST WITH SKI PASS
REMOVAL
(1) Remove rear seat cushion.
(2) Remove seat back fastener.
(3) Remove seat back with arm rest and ski pass
(Fig. 87).
(4) Remove silencer panel fasteners on the back of
seat back (Fig. 88).
(5) Remove silencer panel.
(6) Remove fasteners attaching arm to seat back
(Fig. 89).
(7) Remove arm rest (Fig. 90).
INSTALLATION
(1) Place arm rest into position.
(2) Install fasteners attaching arm rest to seat
back. Tighten fasteners to 5 N·m (46 in. lbs.) torque.
(3) Install silencer fasteners.
(4) Install seat back.
(5) Install seat cushion.
Fig. 84 Rear Door Trim Panel – Typical
Fig. 85 Rear Door Inner Trim Panel – Typical
Fig. 86 Rear Seat Arm Rest – 60/40
300M
BODY
23 - 39
REMOVAL AND INSTALLATION (Continued)
REAR ASSIST HANDLE AND READING LAMP
REMOVAL
(1) Pull down coat hook.
(2) Remove screw holding assist handle to roof
from behind coat hook.
(3) Pull and hold assist handle down.
(4) Remove front screw attaching assist handle to
roof (Fig. 91).
(5) Remove assist handle from roof.
(6) Disengage clips attaching reading lamp socket
to back of assist handle base.
(7) Disconnect reading lamp switch from slot on
back of assist handle base.
(8) Separate assist handle from vehicle.
INSTALLATION
(1) Place assist handle in position on vehicle.
(2) Connect reading lamp switch into slot on back
of assist handle base.
Fig. 87 Arm Rest with Ski Pass
Fig. 88 Rear Seat Silencer
Fig. 89 Rear Seat Arm Rest With Ski Pass
Fig. 90 Arm Rest Removal
Fig. 91 Rear Assist Handle and Reading Lamp
23 - 40
BODY
300M
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст