Chrysler New Yorker. Manual — part 325
(3) Engage clips to attach reading lamp socket to
back of assist handle base.
(4) Place assist handle in position on roof.
(5) Pull and hold assist handle down.
(6) Install front screw to attach assist handle to
roof.
(7) Install screw behind coat hook to attach assist
handle to roof.
REAR SEAT BACK
REMOVAL
(1) Remove rear seat cushion.
(2) Remove fasteners attaching rear seat back and
belts to floor (Fig. 92).
(3) Push rear seat back upward to disengage hooks
at top of seat back.
(4) Remove rear seat from vehicle.
INSTALLATION
(1) Place rear seat in position in vehicle.
(2) Engage hooks at top of seat back.
(3) Install fasteners to attach rear seat back and
belts to floor. Tighten fasteners to 44 N·m (32 ft. lbs.)
torque.
(4) Install rear seat cushion.
REAR SEAT BELT BUCKLE
REMOVAL
(1) Remove rear seat cushion.
(2) Remove seat belt anchor nut (Fig. 93).
(3) Remove seat belt buckle(s) from stud on floor.
INSTALLATION
(1) Place seat belt buckle(s) anchor over stud on
floor.
(2) Install rear seat belt anchor nut. Tighten to 60
N·m (44 ft. lbs.).
(3) Install rear seat cushion.
REAR SEAT BACK – 40 SECTION
REMOVAL
(1) Open door.
(2) Remove seat cushion.
(3) Remove nuts attaching seat back collar assem-
bly.
(4) Remove seat back collar assembly (Fig. 94).
(5) Remove bolt attaching 40 section (Fig. 95).
(6) Slide seat back 40 section off pin and remove
from the collar assembly (Fig. 96).
INSTALLATION
(1) Place seat back 40 section on pin.
(2) Install bolt attaching 40 section seat back to
collar section. Tighten bolt to 60 N·m (44 ft. lbs.)
torque.
(3) Place in position seat back collar assembly.
(4) Install nuts attaching seat back collar assem-
bly. Tighten nuts to 60 N·m (44 ft. lbs.) torque.
(5) Install seat cushion.
Fig. 92 Rear Seat Back
Fig. 93 Rear Seat Belt Buckle(s)
Fig. 94 Collar Assembly
300M
BODY
23 - 41
REMOVAL AND INSTALLATION (Continued)
REAR SEAT BACK – 60 SECTION
REMOVAL
(1) Open door.
(2) Remove rear seat cushion.
(3) Remove nuts attaching seat back collar assem-
bly.
(4) Remove seat back collar assembly.
(5) Remove bolt attaching 40 seat section.
(6) Remove the 40 seat section.
(7) Remove bolt attaching 60 seat section (Fig. 97).
(8) Slide seat back 60 seat section off pin and
remove from the collar assembly.
INSTALLATION
(1) Install the 60 seat section on pin.
(2) Install bolt attaching 60 seat section. Tighten
bolt to 16 N·m (12 ft. lbs.) torque.
(3) Install the 40 seat section on pin.
(4) Install bolt attaching 40 seat section.
(5) Place in position seat back collar assembly.
(6) Install nuts attaching seat back collar assem-
bly. Tighten nuts to 60 N·m (44 ft. lbs.) torque.
(7) Install the rear seat cushion.
REAR SEAT BACK COLLAR ASSEMBLY – 60/40
SEAT
REMOVAL
(1) Open door.
(2) Remove rear seat cushion.
(3) Remove nuts attaching rear seat back collar
assembly.
(4) Remove rear seat back collar assembly.
(5) Remove the 40 seat section from the rear seat
back collar assembly.
(6) Remove the 60 seat section from the rear seat
back collar assembly (Fig. 98).
INSTALLATION
(1) Install the 60 seat section from the rear seat
back collar assembly.
(2) Install the 40 seat section from the rear seat
back collar assembly.
(3) Place in position the rear seat back collar
assembly.
(4) Install nuts attaching rear seat back collar
assembly. Tighten nuts to 60 N·m (44 ft. lbs.) torque.
(5) Install the rear seat cushion.
Fig. 95 Remove 40 Section Seat Back
Fig. 96 40 Section Pivot Pin
Fig. 97 Rear Seat Back 60 Section
23 - 42
BODY
300M
REMOVAL AND INSTALLATION (Continued)
REAR SEAT BELT RETRACTOR
REMOVAL
(1) Remove seat cushion and back.
(2) Remove upper quarter trim panels.
(3) Remove one lower quarter trim panel.
(4) Remove nut attaching lower seat belt anchor to
floor.
(5) Remove turning loop bolt.
(6) Remove bolt attaching belt retractor to quarter
panel.(Fig. 99).
(7) Remove belt from vehicle.
INSTALLATION
(1) Place belt in position on vehicle.
(2) Install bolt to attach belt retractor to quarter
panel.
(3) Install the turning loop.
(4) Install nut to attach lower seat belt anchor to
floor.
(4) Tighten nut to 60 N·m (44 ft. lbs.) torque.
(5) Install lower quarter trim panel.
(6) Install upper quarter trim panels.
(7) Install seat back and cushion.
REAR SEAT CUSHION
REMOVAL
(1) Pull upward at each retainer loop of the rear
seat cushion to disengage retainer loops from cups in
floor (Fig. 100).
(2) Remove rear seat cushion from vehicle.
INSTALLATION
(1) Place rear seat cushion in position in vehicle.
(2) Engage retainer loops into cup on floor kick-up.
(3) Push downward at each retainer loop of the
rear seat cushion to engage retainers.
REAR SEAT CUSHION COVER
REMOVAL
(1) Remove rear seat cushion.
(2) Disengage the J-strap retainers (Fig. 101).
(3) Cut hog rings to free cover (Fig. 102).
(4) Remove seat cushion cover from seat cushion.
INSTALLATION
(1) Position seat cushion cover on cushion.
(2) Install hog rings to seat cover.
(3) Engage the J-strap retainers.
(4) Steam wrinkles from seat cushion, if necessary.
(5) Install seat cushion.
REAR SHELF TRIM PANEL
REMOVAL
(1) Remove seat cushion and back.
(2) Remove quarter trim lower and upper trim
panels.
Fig. 98 Rear Seat Back Collar
Fig. 99 Rear Seat Belt Retractor
Fig. 100 Rear Seat Cushion
300M
BODY
23 - 43
REMOVAL AND INSTALLATION (Continued)
(3) Remove push in fasteners.
(4) Pull rear shelf trim panel away from rear glass
to disengage clips (Fig. 103).
(5) Disengage CHMSL wire connector, if equipped.
(6) Remove rear shelf trim panel from vehicle.
INSTALLATION
(1) Place rear shelf trim panel in position in vehicle.
(2) Connect CHMSL wire connector.
(3) Push parcel shelf trim rearward toward rear
glass and engage clips.
(4) Insert push in fasteners into position.
(5) Install quarter trim lower and upper panels.
(6) Install seat back and cushion.
SUN VISOR
All vehicles with driver and passenger side air
bags must have a colored coded five Bullet point air
bag warning label applied to the sun visor, verify
label availability and ensure the label is installed.
REMOVAL
(1) Remove screw attaching inboard visor retainer
to over head.(Fig. 104).
(2) Remove screws holding outboard visor pivot
base to roof.
(3) Disconnect visor vanity lamp wire connector, if
equipped.
(4) Remove visor from vehicle.
INSTALLATION
(1) Engage visor vanity lamp wire connector, if
equipped.
(2) Place visor in position on header.
(3) Install screws to attach outboard visor pivot
base to over head.
(4) Install screw to attach inboard visor retainer to
over head.
TRUNK CARPET
REMOVAL
(1) Remove rear seat cushion and back.
(2) Remove fasteners at forward edge along wheel
housing.
Fig. 101 Rear Seat Cushion Cover J-Straps
Fig. 102 Rear Seat Cushion Cover Hog Rings
Fig. 103 Parcel Shelf Trim Panel
Fig. 104 Sun Visor
23 - 44
BODY
300M
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст