Chrysler New Yorker. Manual — part 326
(3) Remove spare tire board, jack, and tire.
(4) Remove fasteners at back panel and sides.
(5) Remove carpet.
INSTALLATION
(1) Fold carpet and load into trunk.
(2) Install fasteners.
(3) Install spare tire, jack and board.
(4) Install rear seat back and cushion.
UPPER RADIATOR CLOSURE PANEL
REMOVAL
(1) Open hood.
(2) Mark bolt locations on the upper radiator clo-
sure panel.
(3) Remove bolts attaching windshield washer bot-
tle and speed control servo, if equipped (Fig. 105).
(4) Remove headlamp jackscrews both sides.
(5) Remove fasteners attaching upper bumper fascia.
(6) Remove bolts attaching the forward edge of
upper radiator closure panel.
(7) Remove bolts attaching upper radiator closure
panel.
(8) Disconnect hood latch cable from hood latch.
(9) Remove upper radiator closure panel from vehicle.
(10) For replacement of upper radiator closure
panel, remove hood latch, and any other hardware.
INSTALLATION
(1) Place in position the upper radiator closure
panel.
(2) Connect hood latch cable to hood latch.
(3) Install bolts attaching upper radiator closure
panel. Check bolt alignment marks.
(4) Install bolts attaching the forward edge of
upper radiator closure panel.
(5) Install fasteners attaching upper bumper fascia.
(6) Install headlamp jackscrews both sides.
(7) Check hood latch operation.
WHEELHOUSE SPLASH SHIELD – FRONT
REMOVAL
(1) Hoist and support vehicle on safety stands.
(2) Remove front wheel.
(3) Remove strut assembly from vehicle. Refer to
Group 2, Suspension.
(4) Remove screws attaching speed sensor bracket
(Fig. 106). Move bracket to access speed sensor wire
connector.
(5) Disconnect speed sensor wire connector.
(6) Remove fasteners attaching splash shield to
inner wheelhouse.
(7) Remove splash shield from vehicle.
INSTALLATION
(1) Place splash shield into position.
(2) Install fasteners to attach splash shield.
(3) Connect speed sensor wire connector.
(4) Install screws attaching speed sensor bracket.
(5) Install strut assemble.
(6) Install front wheel.
(7) Lower vehicle.
WHEELHOUSE SPLASH SHIELD – REAR
REMOVAL
(1) Hoist and support vehicle on safety stands.
(2) Remove rear wheel.
(3) Remove fasteners attaching splash shield.
Fig. 105 Upper Radiator Closure Panel
Fig. 106 Wheelhouse Splash Shield
300M
BODY
23 - 45
REMOVAL AND INSTALLATION (Continued)
(4) The shock tower area will have to be cut out of
the splash shield. This will ease the removal or
Installation of the slash shield.
(5) Remove splash shield from vehicle.
INSTALLATION
(1) Place splash shield in position on vehicle with
the shock tower cut out.
(2) Install fasteners to hold splash shield place.
(3) Install rear wheel.
(4) Lower vehicle.
ADJUSTMENTS
FRONT DOOR GLASS ADJUSTMENT
(1) Remove door trim panel.
(2) Remove water shield as necessary.
(3) Loosen fastener attaching scissor channel to
door panel at rear of access hole (Fig. 108).
(4) Position glass in run weatherstrips to achieve
smooth operation and proper fit.
(5) Push glass aft and apply slight downward pres-
sure on scissor channel and tighten screw.
(6) Tighten all fasteners.
(7) Install water shield.
(8) Install door trim panel.
REAR DOOR GLASS ADJUSTMENT
(1) Remove door trim panel.
(2) Remove water shield as necessary.
(3) Loosen fastener attaching scissor channel to
door panel at rear of access hole (Fig. 109).
(4) Position glass in run weatherstrips to achieve
smooth operation and proper fit.
(5) Push glass aft and apply slight downward pres-
sure on scissor channel and tighten screw.
(6) Tighten all fasteners.
(7) Install water shield.
(8) Install door trim panel.
Fig. 107 Rear Wheelhouse Splash Shield
Fig. 108 Front Door Glass Adjustment
Fig. 109 Rear Door Glass Adjustment
23 - 46
BODY
300M
REMOVAL AND INSTALLATION (Continued)
SPECIFICATIONS
BODY GAP AND FLUSH DIMENSIONS
INTREPID
CONCORDE LHS AND 300M – REAR AND SIDE
VIEW
G
Front and Rear Door to Roof
G = 5.0
6
1.5
F = 0 - 1.0
H
Deck Lid To Quarter Panel
G = 4.0
6
1.5
F = 0
6
1.0
I
Tail lamp to applique and Deck Lid
G = 5.0
6
1.5
F = N/A
J
Rear Door to Quarter Panel
G = 5.0
6
1.5
F = 0 + 1.0
K
Front Rear Door To Sill
G = 7.0
6
2.0
F = 0
6
1.5
INTREPID FRONT AND SIDE VIEW
A
Hood to Fender
G = 4.0
6
1
F = 0 - 1.0
B
Hood to Fender Fore and Aft.
G = 0
6
1
F = 0
6
1.0
C
Front Door To Fender
G = 5.0
6
1.5
F = 0 - 1.0
D
Rear Door to Front Door
G = 5.0
6
1.5
F = 0 - 1.0
E
Fuel Filter Door To Quarter
G = 3.0
6
0.75
F = 0 - 1.0
F
Fascia to Hood
G = 5.0
6
2.5
F = 0 - 1.5
Intrepid Front and Side View
INTREPID REAR AND SIDE VIEW
G
Front and Rear Door to Roof
G = 5.0
6
2.5
F = 0 -
6
2.0
H
Deck Lid To Quarter Panel
G = 4
6
1.5
F = 0
6
1.5
I
Tail lamp to applique and Deck Lid
G = 5.0
6
1.5
F = 0
6
2.0
J
Rear Door to Quarter Panel
G = 5.0
6
1.5
F = 0 - 1.0
K
Front Rear Door To Sill
G = 7.0
6
2.0
F = 0
6
2.0
Intrepid Rear and Side View
CONCORDE LHS AND 300M
CONCORDE LHS AND 300M – FRONT AND
SIDE VIEW
A
Hood to Fender
G = 4.0
6
1.5
F = 0
6
1.5
B
Hood to Fender Fore and Aft.
G = 0
6
1
F = 0
6
2.0
C
Front Door To Fender
G = 5.0
6
1.5
F = 0 - 1.0
D
Rear Door to Front Door
G = 5.0
6
1.5
F = 0 - 1.0
E
Fuel Filter Door To Quarter
G = 3.0
6
0.75
F = 0 - 1.5
F
Fascia to Hood
G = 5.0
6
1.5
F = 1.5
6
0.5
Concorde LHS and 300M – Front and Side View
Concorde LHS and 300M – Rear and Side View
300M
BODY
23 - 47
BODY LUBRICATION SPECIFICATIONS
LUBRICATION REQUIREMENTS
Body
mechanisms
and
linkages
should
be
inspected, cleaned, and lubricated, as required, to
maintain ease of operation and to provide protection
against rust and wear. When performing other under
hood services, the hood latch release mechanism and
safety catch should be inspected, cleaned, and lubri-
cated. During the winter season, external door lock
cylinders should be lubricated to assure proper oper-
ation when exposed to water and ice.
Prior to the application of any lubricant, the parts
concerned should be wiped clean to remove dust and
grit. If necessary, a suitable solvent can be used to
clean the item to be lubricated. After lubricating a
component, any excess oil or grease should be
removed.
LUBRICANT APPLICATION
DOOR LOCK CYLINDERS
(1) Apply a small amount of lubricant directly into
the lock cylinder.
(2) Apply a small amount of lubricant to the key.
(3) Insert key into lock cylinder and cycle the
mechanism from the locked to the unlocked position.
NOTE: Do not add more lubricant.
(4) Cycle the lock cylinder mechanism several
times to allow the lubricant to flow throughout the
cylinder.
(5) Wipe all lubricant from exterior of lock cylinder
and key.
ALL OTHER BODY MECHANISMS
(1) Clean component as described above.
(2) Apply specified lubricant to all pivoting and
sliding contact areas of component.
LUBRICANT USAGE
ENGINE OIL
• Door Hinges – Hinge Pin and Pivot Contact
Areas
• Hood Hinges – Pivot Points
• Liftgate Hinges
• Deck lid Hinges
MOPAR
T
SPRAY WHITE CUBE OR EQUIVALENT
• Door Check Straps
• Liftgate Latches
• Liftgate Prop Pivots
• Ash Receiver
• Fuel Filler Door Remote Control Latch Mecha-
nism
• Parking Brake Mechanism
• Sliding Seat Tracks
• Deck lid Latch
MOPAR
T
Multipurpose GREASE OR EQUIVALENT
• All Other Hood Mechanisms
MOPAR
T
LOCK CYLINDER LUBRICANT OR
EQUIVALENT
• Door Lock Cylinders
• Deck lid Lock Cylinder
SPECIAL TOOLS
BODY
Remover, Moldings C-4829
Stick, Trim C-4755
23 - 48
BODY
300M
SPECIFICATIONS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст