Chrysler New Yorker. Manual — part 320
INSTALLATION
(1) Place door latch striker in position on vehicle.
(2) Install bolts to hold striker to B-pillar.
(3) Verify alignment and operation of door, adjust
as necessary.
FRONT DOOR MOUNTED WEATHERSTRIP
REMOVAL
(1) Open front door.
(2) Using a fork type prying tool, disengage push
in fasteners attaching weatherstrip to lower door
(Fig. 39).
(3) Remove weatherstrip from door.
Fig. 35 Door Glass Run Weatherstrip
Fig. 36 Front Door Hinges
Fig. 37 Front Door Latch
300M
BODY
23 - 21
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Place door mounted weatherstrip in position.
(2) Engage push in fasteners to attach weather-
strip to lower door.
(3) Verify door alignment and seal.
FRONT AND REAR DOOR WATER SHIELD
REMOVAL
(1) Remove door trim panel.
(2) Carefully remove water shield from door inner
panel.
INSTALLATION
(1) Apply an appropriate adhesive/sealant to water
shield edges before installing.
(2) Position water shield on door inner panel.
Ensure that the water shield locator holes align.
(3) Press inward on areas with adhesive to attach
shield to inner door. Ensure that the shield is sealed.
(4) Install trim panel.
FRONT DOOR TRIM
REMOVAL
CAUTION:
Do not pry on door trim panel, damage
to trim panel will result.
(1) Remove speaker flag.
(2) Remove speaker grille by inserting trim tool at
the rear of the grille and disengaging clips holding to
trim panel. Remove grille (Fig. 40).
(3) Remove trim plug from the remote bezel by
inserting a small flat blade tool into the notch and
remove, if equipped.
(4) Remove three screws from bottom of door.
(5) Remove screw in pull cup.
(6) Remove screw in remote bezel.
(7) Remove two screws in the instrument panel
interface area.
(8) Remove three screws in the speaker area.
(9) Using an trim tool, disengage the retainer clips
from the door trim panel to the door panel.
(10) Raise trim panel up to disengage from the
belt being careful to hold the panel securely.
(11) Disconnect the linkage from the remote han-
dle assembly (Fig. 41).
(12) Disconnect the power mirror switch.
(13) Disconnect the power door lock switch wire
connector.
(14) Disconnect the power window switch wire con-
nector.
(15) Disconnect the radio speaker wire connector.
(16) Disconnect wiring harness clips from trim
panel.
(17) Disconnect the courtesy lamp.
(18) Remove trim panel from vehicle.
Fig. 38 Front Door Latch Striker
Fig. 39 Front Door Mounted Weatherstrip
Fig. 40 Front Door Trim Panel – Typical
23 - 22
BODY
300M
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Place door trim panel in position.
(2) Install wire harness clips into door trim panel.
(3) Connect the courtesy lamp.
(4) Connect the radio speaker wire connector.
(5) Connect the power window switch wire connec-
tor.
(6) Connect the power door lock switch wire con-
nector.
(7) Connect the power mirror switch wire connec-
tor.
(8) Connect the linkage to the handle assembly.
(9) Install the water shield. Ensure that the water
shield locator holes align. Ensure that the shield is
sealed.
(10) Insert trim panel into channel retainer at top
door.
(11) Insert the forward four way alignment guide
into position. Insert the rearward two way alignment
guide into position.
(12) Install new retaining clips to attach door trim
panel to door panel.
(13) Install three screws in the speaker area.
(14) Install two screws in the instrument panel
interface area.
(15) Install screw in the remote bezel.
(16) Install screw in pull cup. Tighten screw to 1.7
to 2.3 N·m (15 to 20 in. lbs.) torque.
(17) Install three screws to the bottom of the door.
Tighten screws to 1.7 to 2.3 N·m (15 to 20 in. lbs.)
torque.
(18) Install remote bezel trim plug, if equipped.
(19) Place speaker grille in position on trim panel.
Attach door speaker clips to trim panel.
FRONT DOOR WINDOW FRAME MOLDING
REMOVAL
(1) Remove flag trim, speaker, door trim panel,
water shield as necessary, and mirror.
(2) Remove door glass run weatherstrip as neces-
sary to gain access to applique fasteners.
(3) Remove screws attaching molding to window
frame (Fig. 42).
(4) Remove molding from door.
INSTALLATION
(1) Place molding in position on door.
(2) Install screws to attach molding to window
frame.
(3) Install door glass run weatherstrip.
(4) Install the mirror, water shield, door trim
panel, speaker and flag trim.
FRONT SEAT
REMOVAL
(1) Position seat far enough forward to gain access
to rear mount bolts on floor.
(2) Remove bolts holding rear of seat track to floor
(Fig. 43).
(3) Slide seat rearward.
(4) Remove bolts holding front of the seat track to
floor kick up.
(5) Disconnect front seat wire harness connector
from body harness connector.
(6) Remove front seat from vehicle.
Fig. 42 Front Door Frame Window Molding
Fig. 41 Inner Front Door Trim Panel – Typical
300M
BODY
23 - 23
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
NOTE: Ensure that the seat tracks are rearward
(1) Place front seat in position in vehicle.
(2) Connect front seat wire harness connector to
body harness connector.
(3) Install bolts to attach front of seat track to the
floor kick up. Tighten bolts to 42 N·m (31 ft. lbs.)
torque.
(4) Slide seat forward and install bolts attaching
rear of seat track to the floor. Tighten bolts to 42
N·m (31 ft. lbs.) torque.
(5) Verify front seat operation.
FRONT SEAT ARM REST – CONCORDE/INTREPID
REMOVAL
(1) Slide the driver seat full forward and the pas-
senger seat full rearward.
(2) Open arm rest lid (Fig. 44).
(3) Remove access retaining nut cover.
(4) Remove arm rest retaining nut.
(5) Slide arm rest off of bracket (Fig. 45).
INSTALLATION
(1) Slide arm rest on bracket.
(2) Install arm rest nut. Tighten nut to 25 N·m (18
ft. lbs) torque.
(3) Install access retaining nut cover.
(4) Reposition the seats.
Fig. 43 Front Seat Removal
Fig. 44 Arm Rest Access Hole
Fig. 45 Arm Rest Bracket
23 - 24
BODY
300M
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст