Chrysler New Yorker. Manual — part 321
FRONT SEAT BACK
REMOVAL
(1) Remove seat from vehicle.
(2) Remove seat cushion side shields.
(3) Remove bolts attaching recliner to seat back
cushion frame (Fig. 46).
(4) Remove inboard pivot bolt (Fig. 47).
(5) Connect any electrical connectors to the seat
back, if equipped.
(6) Separate seat back from seat cushion.
INSTALLATION
(1) Position seat back on cushion.
(2) Connect electrical connectors to the seat back,
if equipped.
(3) Install inboard pivot bolt. Tighten bolt to 30
N·m (22 ft. lbs.) torque.
(4) Install bolts attaching recliner to seat cushion
frame. Tighten bolts to 14 N·m (10 ft. lbs.) torque.
(5) Install seat cushion side shields.
(6) Install seat in vehicle.
FRONT SEAT BACK COVER
REMOVAL
(1) Remove seat from vehicle.
(2) Remove head rest.
(3) Remove front seat back.
(4) Remove lumbar support handle, if equipped.
(5) Disengage the J-strap retainer (Fig. 47).
(6) Roll cover upward to hog rings. Cut hog rings
to free cover (Fig. 48).
(7) Roll cover to top of cushion and remove head
rest sleeve guides.
(8) Remove cover from seat back.
INSTALLATION
NOTE: Do not reuse the recliner assembly attach-
ing bolts.
(1) Position cover at the top of seat back.
(2) Carefully roll cover down to the area that hog
rings are to be installed.
(3) Install hog rings.
(4) Roll cover downward.
(5) Engage the J-strap retainer.
(6) Install lumbar support handle, if equipped.
(7) Install new head rest sleeve guides.
(8) Install seat back to seat cushion. Tighten bolts
to 30 N·m (22 ft. lbs.) torque.
(9) Install seat in vehicle.
(10) Install head rest.
(11) Check seat back operation.
FRONT SEAT BELT RETRACTOR
Inspect the condition of the shoulder belt and lap
belt. Replace any belt that is cut, frayed, torn, or
damaged in any way. Also, replace the shoulder belt
if the retractor is either damaged or inoperative.
REMOVAL
(1) If necessary, move the front seat(s) all the way
forward for access.
Fig. 46 Recliner Attaching Bolt
Fig. 47 Remove Seat Back
Fig. 48 Front Seat Back Hog Rings
300M
BODY
23 - 25
REMOVAL AND INSTALLATION (Continued)
(2) Detach the turning loop cover from the upper
anchor bolt.
(3) Remove upper anchor bolt (Fig. 49).
(4) Remove B-pillar upper trim.
(5) Remove lower anchor bolt.
(6) Remove the retractor anchor bolt.
(7) Disconnect retractor wire harness connector.
(8) Remove retractor from vehicle.
INSTALLATION
(1) Position the retractor in the vehicle.
(2) Install the retractor anchor bolt. Tighten to 60
N·m (44 ft. lbs.) torque.
(3) Connect retractor wire harness connector.
(4) Install the lower anchor bolt. Tighten to 60
N·m (44 ft. lbs.) torque.
(5) Route the belt webbing through the access slots
in B-pillar upper trim.
(6) Install B-pillar upper trim.
(7) Install the upper anchor bolt. Tighten to 60
N·m (44 ft. lbs.) torque.
(8) Close turning loop covers.
FRONT SEAT CENTER OCCUPIED BELT BUCKLE –
CONCORDE/INTREPID
REMOVAL
(1) Move or remove front seat as necessary to gain
access to seat belt buckle anchor bolt.
(2) Remove bolt attaching buckle and reinforce-
ment to front seat track (Fig. 50).
(3) Remove seat belt buckle from vehicle.
INSTALLATION
(1) Place seat belt buckle in position on vehicle.
(2) Install bolt attaching buckle and reinforcement
to front seat track or floor. Tighten bolt to 60 N·m (44
ft. lbs.) torque.
(3) Install front seat, if it was removed.
FRONT SEAT CUSHION
REMOVAL
(1) Remove seat from vehicle.
(2) Remove front seat cushion side shields and dis-
connect wire connectors, if equipped.
(3) Remove seat back.
(4) Remove track and recliner assembly.
(5) Disconnect seat cushion heater element connec-
tor, if equipped.
(6) Disconnect wire harness fasteners from cushion
frame (Fig. 51).
(7) Remove seat cushion (Fig. 52).
INSTALLATION
(1) Install
wire
harness
fasteners
to
cushion
frame.
(2) Connect seat cushion heater element connector,
if equipped.
(3) Install track and recliner assembly.
(4) Install seat back. Tighten bolts to 30 N·m (22
ft. lbs.) torque.
(5) Connect switch wire connectors to the cushion
side shield, if equipped.
(6) Install cushion side shields.
(7) Install seat in vehicle.
Fig. 50 Front Seat Center Occupied Belt Buckle –
Typical
Fig. 49 Front Shoulder Belt Adjuster
23 - 26
BODY
300M
REMOVAL AND INSTALLATION (Continued)
FRONT SEAT CUSHION COVER
REMOVAL
(1) Remove seat from vehicle.
(2) Remove front seat cushion side shields.
(3) Remove seat back.
(4) Remove track and reclined assembly.
(5) Disengage J-strap attaching seat cover from
the seat cushion frame(Fig. 53).
(6) Pull cover off to the hog rings (Fig. 54).
(7) Cut hog rings attaching seat cover seat cush-
ion.
(8) Route seat function switches through access
hole on outboard side of seat cushion, if equipped.
(9) Disconnect seat cushion heater element connec-
tor, if equipped.
(10) Separate seat cushion cover from seat cush-
ion.
INSTALLATION
(1) Position seat cover on cushion.
(2) Align seat cover with cushion alignment inden-
tations.
(3) Engage seat cushion heater element connector,
if equipped.
(4) Install hog rings.
(5) Engage J-strap attaching seat cover to front of
seat cushion frame.
(6) Install track and recliner assembly.
(7) Install seat back.
(8) Install front seat cushion side shields.
(9) Install seat in vehicle.
FRONT SEAT CUSHION SIDE SHIELD
REMOVAL
(1) Remove seat from vehicle.
(2) Remove screws attaching seat cushion side
shield to the bottom and side of seat cushion (Fig. 56)
and (Fig. 57).
(3) Remove shield from seat.
(4) Disconnect switch wire connectors, if equipped.
(5) Remove seat switches, if equipped.
INSTALLATION
(1) Transfer seat switches, if equipped.
(2) Connect switch wire connectors to cushion side
shield, if equipped.
Fig. 51 Front Seat Cushion Wire Harness
Fig. 52 Front Seat Cushion
Fig. 53 Front Seat Cushion J- Strap
Fig. 54 Seat Cushion Cover
300M
BODY
23 - 27
REMOVAL AND INSTALLATION (Continued)
(3) Place shield in position on seat cushion.
(4) Install screws attaching seat cushion side
shield.
(5) Install seat. Tighten front screws to 60 N·m (44
ft. lbs.), and the rear screws to 48 N·m (35 ft. lbs.).
FRONT SEAT HEAD REST
REMOVAL
(1) Lower head rest slightly.
(2) Insert a stiff wire into the hole on the right
hand side head rest sleeve/guide and push to release
latch (Fig. 58).
(3) At the same time, press the button on the head
rest sleeve/guide left hand side and pull upward to
release the head rest.
(4) Remove head rest from seat back.
INSTALLATION
(1) Place head rest in position.
(2) Push head rest down into the lock position.
(3) Raise head rest to ensure it locks at the last
stop.
FRONT SEAT LUMBAR SUPPORT
The front seat lumbar support is not service sepa-
rately. The front seat back frame will need to be
replaced.
FRONT SEAT TRACK AND RECLINER
REMOVAL
(1) Remove front seat from vehicle.
(2) Remove seat cushion side shield and disconnect
switch connector, if equipped.
(3) Remove bolt attaching seat back recliner to
seat back frame on each side of seat (Fig. 59).
(4) Remove bolts attaching seat track and recliner
to cushion frame (Fig. 60).
(5) Remove seat track and recliner from seat cush-
ion.
INSTALLATION
(1) Place seat track in position on seat cushion.
(2) Install bolts to attach seat track and recliner to
cushion frame.
(3) Install bolt to attach seat back recliner to seat
back on each side of seat. Tighten bolt to 30 N·m (22
ft. lbs.) torque.
(4) Connect wire connectors and install the cush-
ion side shields.
(5) Install front seat in vehicle.
Fig. 55 Seat Cushion Alignment Indentations
Fig. 56 Bottom View of Side Shield
Fig. 57 Side View of Side Shield
Fig. 58 Head Rest Removal
23 - 28
BODY
300M
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст