Chrysler New Yorker. Manual — part 94
LAMP BULB SERVICE
INDEX
page
page
REMOVAL AND INSTALLATION
CHMSL LAMP BULB . . . . . . . . . . . . . . . . . . . . . . 13
CITY LAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . 9
FRONT FOG LAMP BULB . . . . . . . . . . . . . . . . . 10
FRONT PARKING, SIDE MARKER, AND TURN
SIGNAL LAMP BULB . . . . . . . . . . . . . . . . . . . . . 9
HEADLAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . 8
REAR LICENSE PLATE LAMP BULB . . . . . . . . . 12
SIDE REPEATER LAMP BULB . . . . . . . . . . . . . . 11
TAIL, STOP, BACKUP, FOG LAMP AND TURN
SIGNAL BULBS . . . . . . . . . . . . . . . . . . . . . . . . 11
REMOVAL AND INSTALLATION
HEADLAMP BULB
Removal
(1) Hoist Vehicle.
(2) Partially remove the front fascia to gain access
to the headlamp assembly. Refer to Group 13, Frame
and Bumpers for Removal and Installation proce-
dures.
(3) Remove the jackscrews attaching the headlamp
assembly to the crossmember (Fig. 1).
(4) Pull the headlamp assembly out and disconnect
the electrical connectors (Fig. 2).
(5) Twist and remove the appropriate bulb from
the headlamp assembly (Fig. 3).
(6) Remove the electrical connector from the bulb.
Installation
CAUTION: Do not touch the bulb glass with fingers
or other oily surfaces. Reduced bulb life will result.
(1) Twist the new bulb into the headlamp assembly.
Fig. 1 Headlamp Jackscrews
Fig. 2 Headlamp Assembly Removal
Fig. 3 Headlamp Bulb
8L - 8
LAMPS
300M
(2) Reconnect the headlamp assembly electrical
connectors and slide the headlamp assembly back
into the crossmember.
(3) Install the headlamp jackscrews (Fig. 1).
(4) Reinstall the front fascia. Refer to Group 13,
Frame and Bumpers for Removal and Installation
procedures.
(5) Lower vehicle from hoist.
FRONT PARKING, SIDE MARKER, AND TURN
SIGNAL LAMP BULB
Removal
(1) Remove the front fog lamp assembly. Refer to
the Front Fog Lamp Assembly Removal and Installa-
tion procedures.
(2) Reach up through the front fascia and rotate
the bulb socket.
(3) Pull the bulb socket from the lamp housing
(Fig. 4).
(4) Pull the bulb from the socket.
Installation
(1) Push the bulb into the socket.
(2) Install the socket into the lamp housing.
(3) Install the fog lamp assembly.
CITY LAMP BULB
Removal
(1) Remove the headlamp assembly. Refer to the
Headlamp Assembly removal and Installation proce-
dures.
(2) Twist and remove the city lamp socket housing
from the headlamp assembly (Fig. 5).
(3) Pull the city lamp bulb from the socket housing
(Fig. 6).
Installation
(1) Push the new city lamp bulb into the city lamp
housing.
(2) Install the city lamp socket housing into the
headlamp assembly.
(3) Install the headlamp assembly.
Fig. 4 Front Parking, Side Marker, and Turn Signal
Lamp Bulb
Fig. 5 City Lamp Housing
Fig. 6 City Lamp Bulb
300M
LAMPS
8L - 9
REMOVAL AND INSTALLATION (Continued)
FRONT FOG LAMP BULB
Removal
(1) Remove the front fog lamp attaching screws
(Fig. 7).
(2) Pull the fog lamp assembly from the bumper
fascia and disconnect the electrical connector (Fig. 8).
(3) Remove the fog lamp assembly rear cover from
the fog lamp assembly (Fig. 9).
(4) Disengage the fog lamp bulb retaining wire and
remove the bulb from the fog lamp assembly (Fig.
10).
Installation
(1) Install bulb into the fog lamp assembly and
reattach the retaining wire.
(2) Cover exposed terminals with protective sleeve.
(3) Install the rear cover on the fog lamp assembly.
Fig. 7 Front Fog Lamp
Fig. 8 Front Fog Lamp Electrical Connector
Fig. 9 Front Fog Lamp Assembly Rear Cover
Fig. 10 Front Fog Lamp Bulb
8L - 10
LAMPS
300M
REMOVAL AND INSTALLATION (Continued)
(4) Connect the electrical connector and place the
fog lamp assembly into the front bumper fascia.
(5) Install the fog lamp assembly attaching screws.
SIDE REPEATER LAMP BULB
Removal
(1) Insert a small flat screwdriver between the
lamp and the body panel. Disengage the lamp retain-
ing tabs (Fig. 11) (Fig. 12).
(2) Pull lamp from fender.
(3) Twist the bulb socket 1/4 turn and separate the
bulb socket from the lamp (Fig. 13).
(4) Pull the bulb from the socket.
Installation
(1) Insert the bulb into the socket.
(2) Position the socket in the lamp and twist the
socket 1/4 turn.
(3) Position the lamp into the body opening and
push into place.
TAIL, STOP, BACKUP, FOG LAMP AND TURN
SIGNAL BULBS
Removal
(1) Release the deck lid latch and open the deck
lid.
(2) Remove the tail lamp assembly attaching nuts
(Fig. 14).
Fig. 11 Side Repeater Lamp
Fig. 12 Side Repeater Lamp Retaining Tabs
Fig. 13 Side Repeater Lamp Socket
Fig. 14 Tail Lamp Assembly Fasteners
300M
LAMPS
8L - 11
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст