Chrysler Town & Country/Voyager, Dodge Caravan, Plymouth Voyager. Manual — part 118
BUCKET SEAT RISER TRIM COVER
REMOVAL (FIG. 15)
(1) Remove screw holding riser trim cover to seat
riser crossmember.
(2) Separate trim cover from seat riser.
INSTALLATION
Reverse the preceding operation.
BUCKET SEAT RISER
REMOVAL (FIG. 16)
(1) Remove seat from vehicle. Refer Body Compo-
nent Service section for front seat procedures. Refer to
Owner’s Manual for rear seat procedures.
(2) Remove storage drawer, if equipped.
(3) Remove nuts holding riser to bottom of seat.
(4) Separate riser from seat.
INSTALLATION
Reverse the preceding operation.
BUCKET SEAT CUSHION SIDE COVER
REMOVAL (FIG. 17)
(1) Remove recliner handle, if equipped.
(2) Disengage seat belt buckle tether from side cover,
if equipped.
(3) Remove screws holding side cover to seat cushion
frame.
(4) Separate side cover from seat.
INSTALLATION
Reverse the preceding operation.
BUCKET SEAT CUSHION FRAME
REMOVAL (FIG. 18)
(1) Remove seat from vehicle. Refer Body Compo-
nent Service section for front seat procedures. Refer to
Owner’s Manual for rear seat procedures.
(2) Remove riser.
(3) Separate seat back from cushion.
(4) Disengage J-strip retainers from cushion frame.
(5) Separate frame from pad.
INSTALLATION
Reverse the preceding operation.
BUCKET SEAT CUSHION PAD
REMOVAL (FIG. 19)
(1) Remove seat from vehicle. Refer Body Compo-
nent Service section for front seat procedures. Refer to
Owner’s Manual for rear seat procedures.
(2) Separate riser from seat.
(3) Separate seat back from cushion.
(4) Disengage J-strip retainers from cushion frame.
Fig. 15 Bucket Seat Riser Trim Cover
Fig. 16 Bucket Seat Riser
Fig. 17 Bucket Seat Cushion Side Cover
.
BODY
23 - 11
(5) Disengage hook/loop fasteners holding cover to
pad.
(6) Remove hog-rings holding listing wire to hold
down wire in pad.
(7) Separate cover from pad.
BUCKET SEAT CUSHION PAD INSTALLATION
(FIG. 20)
(1) Center listing wire in pull down groove.
(2) Hog-ring listing wire to pull down wire in pad.
(3) Reverse steps 5 through 1 of preceding operation.
SECOND REAR SEAT BACK PANEL
REMOVAL (FIG. 21)
(1) Remove screws holding rear panel to seat back.
(2) Lift upward on base of panel and pull rearward
to disengage hooks holding top of panel to seat back.
(3) Separate panel from seat back.
INSTALLATION
Reverse the preceding operation.
SECOND REAR SEAT BACK HINGE COVER
REMOVAL (FIG. 22)
(1) Remove screw holding hinge cover to seat back
hinge.
(2) Separate cover from seat back hinge.
INSTALLATION
Reverse the preceding operation.
SECOND REAR SEAT BACK
REMOVAL (FIG. 23)
(1) Remove seat back hinge covers.
(2) Remove bolts holding bottom of seat back hinges
to cushion frame.
(3) Separate seat back from cushion.
Fig. 19 Seat Cushion Cover Listing and Hook/Loop
Fasteners
Fig. 18 Bucket Seat Cushion Frame
Fig. 20 Hog-ring Cover Listing to Pull Down
Fig. 21 Second Rear Seat Back Panel
23 - 12
BODY
.
SECOND REAR SEAT BACK INSTALLATION
Reverse the preceding operation.
SECOND REAR SEAT BACK HINGE
REMOVAL (FIG. 24)
(1) Remove seat back hinge cover.
(2) Remove bolts holding seat back hinge to cushion
frame.
(3) Remove nuts holding hinge to seat back.
(4) Separate seat back hinge from seat.
INSTALLATION
Reverse the preceding operation.
SECOND REAR SEAT TRACK
REMOVAL (FIG. 25)
(1) Remove second rear seat from vehicle.
(2) Position seat upside down on a clean work sur-
face.
(3) Disconnect track adjuster link wire from latch
arm.
(4) Remove nuts holding track to riser.
(5) Separate track from riser.
INSTALLATION
Reverse the preceding operation.
SECOND REAR SEAT RISER
REMOVAL (FIG. 26)
(1) Remove seat track, if equipped.
(2) Remove bolts holding riser to bottom of seat
frame.
(3) Separate riser from seat.
INSTALLATION
Reverse the preceding operation.
Fig. 22 Second Rear Seat Back Hinge Cover
Fig. 23 Second Rear Seat Back
Fig. 24 Second Rear Seat Back Hinge
Fig. 25 Second Rear Seat Track
.
BODY
23 - 13
SECOND REAR SEAT CUSHION PAD
REMOVAL
(1) Remove seat from vehicle.
(2) Position seat on a clean work surface.
(3) Separate seat back hinges from cushion frame.
(4) Remove seat risers.
(5) Remove seat belts from rear rail of seat cushion
frame.
(6) Disengage J-strip retainers holding trim cover to
bottom cushion frame.
(7) Separate frame from cushion pad and cover.
(8) Turn cushion pad upright on work surface.
(9) Roll cover inside out to top of cushion pad.
(10) Remove hog-rings holding cover listing wire to
hold down wire in cushion pad. Refer to Bucket Seat
Cushion Pad paragraph for typical illustrations.
(11) Separate cover from pad.
INSTALLATION
Reverse the preceding operation.
SECOND REAR SEAT BACK PAD
REMOVAL
(1) Remove seat back hinge covers.
(2) Remove bolts holding hinges to cushion frame.
(3) Separate seat back from cushion.
(4) Position seat back on a clean work surface.
(5) Remove seat back trim panel.
(6) Remove hog-rings holding cover to seat back
frame.
(7) Separate frame from back pad and cover.
(8) Turn back pad upright on work surface.
(9) Roll cover inside out to top of back pad.
(10) Remove hog-rings holding cover listing wires to
hold down wires in pad. Refer to Bucket Seat Back Pad
paragraph for typical illustrations.
(11) Separate cover from back pad.
INSTALLATION
Reverse the preceding operation.
CHILD RESTRAINT SEAT
The child restraint, two passenger seat, located in
the first rear position can be removed from the vehicle
using instructions provided in the Owner’s manual.
CHILD SEAT MODULE
REMOVAL
(1) Remove trim panel from rear of seat back.
(2) Open child seat and separate hook and loop
fasteners holding vinyl insert to module.
(3) Disengage J-strip retainer holding head re-
straint trim cover to seat back frame.
(4) Remove hog-rings holding seat back trim cover to
upper seat back frame (Fig. 27).
(5) Disengage push-in fasteners holding seat back
trim cover to module under head restraint.
(6) Pull seat back trim cover from under head re-
straint.
(7) Remove screws holding top of module to seat
back frame (Fig. 28).
(8) Close child restraint seat.
(9) Deflect pad at base of module upward to gain
access to hidden screws under module.
(10) Remove screws holding bottom of module to
seat back frame (Fig. 28).
(11) Rotate top of module forward while pulling
upward and separate module from seat back.
INSTALLATION
Reverse the preceding operation.
Fig. 26 Second Rear Seat Riser—Typical
Fig. 27 Seat Back Cover Hog-ring
23 - 14
BODY
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст