SsangYong Korando II (1996-2006 year). Manual — part 153
OM600 ENGINE MECHANICAL 1B3 -- 61
DAEWOO MY_2000
38. Replace the O--ring of heater feed pipe and install it
to the cylinder head.
Notice
For installation, clean the hole.
39. Install the bracket of heater feed pipe to the oil filter.
40. Install the fuel pipe and the accelerator control link-
age.
41. Connect the fuel lines to the injection nozzles and to
the injection pump.
Tightening Torque
18 N∙m (13 lb-ft)
Box Wrench Insert 000 589 77 03 00
1B3 -- 62 OM600 ENGINE MECHANICAL
DAEWOO MY_2000
42. Install the poly V--belt.
Notice
Be careful not to contaminate the belt.
43. By inserting a rod into the tensioning lever upper
hole and pulling the rod, install the bolt and then
tighten the nut.
Tightening Torque
23 N∙m (17 lb-ft)
44. Install the oil dipstick tube bracket.
Tightening Torque
10 N∙m (89 lb-in)
45. Hold the cooling fan with the counter holder and
tighten the bolt.
OM600 ENGINE MECHANICAL 1B3 -- 63
DAEWOO MY_2000
TIMING CASE COVER
Preceding Work : Removal of the cooling fan
Rmoval of the V--belt tensioning device
Removal of the vibration damper and hub
Removal of the generator
1 Bolt
10N∙m (89 lb-in)
. . . . . . . . . . . . . . . . . . . . .
2 Cylinder Head Cover
3 Gasket
Replace
. . . . . . . . . . . . . . . . . . . . . . . . . .
4 Socket Bolt
25N∙m (18 lb-ft)
. . . . . . . . . . . . . . . .
5 Fuel Filter
6 Square Nut
7 Oil Pan
8 Socket Bolt
10N∙m (89 lb-in)
. . . . . . . . . . . . . . .
9 Bolt
M6 : 10N∙m (89 lb-in)
. . . . . . . . . . . . . . . .
M8 : 23N∙m (17 lb-ft)
10 Power Steering Pump
11 Bolt
12 Belt Pulley
13 Bolt
32N∙m (24 lb-ft)
. . . . . . . . . . . . . . . . . . . . . .
14 Timing Case Cover
15 Bolt
23N∙m (17 lb-ft)
. . . . . . . . . . . . . . . . . . . . . .
16 Generator Bracket
17 Bolt
45N∙m (33 lb-ft)
. . . . . . . . . . . . . . . . . . . . . .
18 Bolt
25N∙m (18 lb-ft)
. . . . . . . . . . . . . . . . . . . . . .
19 Bolt
10N∙m (89 lb-in)
. . . . . . . . . . . . . . . . . . . . .
20 Closing Cover
21 Socket Bolt
23N∙m (17 lb-ft)
. . . . . . . . . . . . . . . .
22 Guide Pulley
23 Bolt
9N∙m (80 lb-in)
. . . . . . . . . . . . . . . . . . . . . . .
24 Guide Pulley Bracket
25 Nut
23N∙m (17 lb-ft)
. . . . . . . . . . . . . . . . . . . . . . .
1B3 -- 64 OM600 ENGINE MECHANICAL
DAEWOO MY_2000
Tools Required
116 589 03 07 00 Socket Wrench
Removal Procedure
1. Remove the fan clutch and cooling fan belt pulley.
2. Drain the engine oil completely.
3. Remove the oil dipstick tube bracket bolts.
4. Remove the crankshaft pulley.
5. Loosen the bolt (1) and then remove the cylinder
head cover (2) and gasket.
6. Remove the vacuum pump.
7. Detach the closing cover (20). Remove the bolts(21)
and then remove the guide pulley (22).
8. Remove the guide pulley bracket (24).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст