SsangYong Korando II (1996-2006 year). Manual — part 221
SSAMGYONG MY2002
3A-20 FRONT AXLE
2. Assemble the parts of the drive pinion.
3. Assemble the parts of the differential carrier.
4. Measure backlash of the side gear and pinion.
Assembly Procedure
1. Clean the all parts and check the followings :
•
Check the ring gear and drive pinion for wear
and damage. If damaged, replace it as a set.
•
Check the bearing for sticks, wear, noise and
turning resistance.
•
Check the side gear, pinion, pinion shaft and
thrust washer for wear and damage.
•
Check the differential carrier for crack and wear
(bearing contact surface). Check the gear case
for crack.
KAA3A420
KAA3A430
KAA3A660
KAA3A420
Tightening Torque
of the Lock Nut
240 - 310 N•m
(177 - 229 lb-ft)
Tightening Torque
of the Ring Gear Bolts
75 - 90 N•m
(55 - 66 lb-ft)
Standard
0.025 mm
FRONT AXLE 3A-21
SSANGYONG MY2002
5. Install the differential carrier assembly into the axle
housing.
Notice: Be careful not to change the caps. Be
sure to keep the original position of the caps.
6. Measure backlash of the drive pinion and ring
gear.
Tightening Torque of
the Bearing Cap Bolts
4.8 - 6.9 kgf•m
KAA3A670
KAA3A360
KAA3A440
KAA3A680
7. Install the axle housing cover.
8. Assemble the parts of the front axle shaft and
housing mounting bracket.
Notice: Apply grease to the oil seal rib.
Specified Value
0.165 mm
Tightening Torque
3.9 - 4.6 kgf•m
SSAMGYONG MY2002
3A-22 FRONT AXLE
1. Heel contact
2. Toe contact
3. Face contact
4. Flank contact
Adjust backlash
(Drecrease backlash)
•
Select proper shim(s) to
move the drive pinion
toward the ring gear
(toward toe)
Adjust backlash
(Increase backlash)
•
Select proper shim(s) to
move the drive pinion
against the ring gear
(toward heel)
Adjust backlash
(Increase pinion shim)
•
Move the drive pinion
toward the ring gear
(toward center of ring
gear)
Adjust backlash
(Decrease pinion shim)
•
Move the ring gear toward
the drive pinion (toward
ring gear center line)
Excessive backlash (little)
•
Noise can be occurred
Insufficient backlash (little)
•
Tooth can be damaged
or broken under heavy
load
Excessive backlash (much)
•
Drive pinion shaft is
apart from the ring gear
•
Noise can be occurred
Insufficient backlash (much)
•
Gear contacts on the
low flank
•
Gear can be damaged
or worn
•
Noise can be occurred
Inspection of Ring Gear Tooth Contact
Pattern
Normal Contact
Apply gear-marking compound (Prussian blue / red
lead) on the ring gear teeth. Rotate the ring gear and
check the tooth contact pattern.
KAA3A450
Abnormal Contact
Tooth contact pattern
Possible cause
Remedy
KAA3A460
KAA3A470
KAA3A480
KAA3A500
KAA3A510
KAA3A520
KAA3A490
KAA3A530
FRONT AXLE 3A-23
SSANGYONG MY2002
KAA3A550
KAA3A540
OUTER JOINT SEAL
Tools Required
J-8059
Snap Ring Plier
Disassembly and Assembly Procedure
1. Remove the front drive shaft from the vehicle.
Refer to “Front Drive Shaft” in this section.
2. Remove the large seal retaining clamp.
3. Remove the small seal retaining clamp.
4. Degrease the joint.
Installation Notice:
•
Fill the joint seal with 135 to 155 g (4.76 to 5.46
ounces) of the recommended grease. Repack
the joint with 135 to 155 g (4.76 to 5.46 ounces)
of the recommended grease.
5. Spread the snap ring using the snap ring plier J-
8059 and remove the outer joint from the front drive
shaft.
Caution: Do not disassembly the outer joint
assembly. Parts are match fit and cannot be
serviced separately. Improper reassembly will
adversely affect both performance and safety.
6. Remove the seal from the joint assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст