SsangYong Korando II (1996-2006 year). Manual — part 133
M161 ENGINE INTAKE & EXHAUST 1G2 -- 7
DAEWOO MY_2000
Removal & Installation Procedure
1. Release the clamp (1) and intake air duct.
2. Remove the Blow--by hose (5) (arrow).
3. Release the clamp (7) and remove the intake air duct.
Notice: Completely fit the intake air duct with the mount-
ing bracket (8).
1G2 -- 8 M161 ENGINE INTAKE & EXHAUST
DAEWOO MY_2000
INTAKE MANIFOLD
Preceding Work: Removal of intake air duct
Removal of fuel distributor and injector valve
1 Bolt (M6 X 40, 6 pieces)
22.5--27.5 NSm (16.6--20.3 lb-ft)
. . . . . . . . . . . . .
2 Intake Manifold
3 Gasket (2 pieces)
Replace
. . . . . . . . . . . . . . . . . .
4 Bolt (M8 X 40, 3 pieces)
22.5--27.5 NSm (16.6--20.3 lb-ft)
. . . . . . . . . . . . .
5 Idle Regulator
6 Intermediate Flange
7 Bolt (M6 X 35, 4 pieces)
9--11 NSm (80--97 lb-in)
. . . . . . . . . . . . . . . . . . . . .
8 Connection Piece With Seal Ring
36--44 NSm (27--33 lb-ft)
. . . . . . . . . . . . . . . . . . . .
M161 ENGINE INTAKE & EXHAUST 1G2 -- 9
DAEWOO MY_2000
Removal & Installation Procedure
1. Disconnect the battery ground cable.
2. Remove idle speed control plug connector (arrow).
3. Disconnect the brake booster vacuum line and other
vacuum lines.
4. Disconnect the rod from bearing bracket assembly
and remove the connection piece (8).
Installation Notice
Tightening Torque
36 -- 44 NSm (27 -- 33 lb-ft)
5. Unscrew the three bolts (4) and remove the idle regu-
lator and intermediate flange (6).
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
6. Unscrew the two bolts (M8 X 16) and remove the sup-
port assembly.
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
7. Unscrew the intake manifold mounting bolts (1) and
remove the intake manifold and gasket.
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
Notice: Replace the gasket with new one.
8. Installation should follow the removal procedure in
the reverse order.
9. Start the engine and check for leaks in each connec-
tion.
1G2 -- 10 M161 ENGINE INTAKE & EXHAUST
DAEWOO MY_2000
EXHAUST MANIFOLD
1 Oxygen Sensor
55 NSm (41 lb-ft)
. . . . . . . . . . . .
2 Bolt (4 pieces)
9--11 NSm (80--97 lb-in)
. . . . . . . .
3 Upper Cover
4 Nut (11 pieces)
31.5--38.5 NSm (23.2--28.4 lb-ft)
. . . . . . . . . . . . .
5 Exhaust Manifold
6 Flange Bolt & Exhaust Pipe
Mounting Nut
30 NSm (22 lb-ft)
. . . . . . . . . . . . . .
7 Gasket
Replace
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст