SsangYong Korando II (1996-2006 year). Manual — part 16
1B1 -- 30 M162 ENGINE MECHANICAL
DAEWOO MY_2000
7. Remove the cylinder head bolts in numerical order
using allen wrench socket 617 589 00 10 00.
Installation Notice
Ti ht i
T
1st step: 55 NSm
(41 lb-ft)
Tightening Torque
2nd step: 90°
3rd step: 90°
8. Check the length of the cylinder head bolt.
Installation Notice
Length (L)
New 160 ± 0.8 mm
Length (L)
Max. 162 ± 0.7 mm
D
Replace the bolt if the measured length exceed
the max. length.
D
Apply the oil to the thread surface of bolt.
9. Carefully remove the cylinder head and check the
mating surface.
10. Installation should follow the removal procedure in
the reverse order.
M162 ENGINE MECHANICAL 1B1 -- 31
DAEWOO MY_2000
TIMING GEAR CASE COVER
Preceding Work: Removal of cylinder head front cover
Removal of generator bracket
Removal of tensioning device
Removal of belt pulley and vibration damper
1 Bolt (M8 x 60, 3 pieces)
22.5--27.5 NSm (16.6--20.3 lb-ft)
. . . . . . . . . . . . .
2 A/C Bracket
3 Bolt (M8 x 65, 3 pieces)
22.5--27.5 NSm (16.6--20.3 lb-ft)
. . . . . . . . . . . . .
4 Bolt (M8 x 40, 1 piece)
22.5--27.5 NSm (16.6--20.3 lb-ft)
. . . . . . . . . . . . .
5 Bolt (M8 x 60, 1 piece)
22.5--27.5 NSm (16.6--20.3 lb-ft)
. . . . . . . . . . . . .
6 Seal
7 Timing Gear Case Cover
8 Roll Pin
9 Bolt (M6 x 22, 6 pieces)
9--11 NSm (80--97 lb-in)
. . . . . . . . . . . . . . . . . . . . .
1B1 -- 32 M162 ENGINE MECHANICAL
DAEWOO MY_2000
Removal & Installation Procedure
1. Put the alignment marks (arrows) on the timing chain
and camshaft sprocket.
2. Unscrew the A/C bracket bolts (1) and remove the
bracket.
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
3. Remove the cooling fan and the viscous clutch. Un-
screw the three bolts from the cooling fan bracket and
remove the bracket (arrows).
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
4. Remove the timing gear case cover after unscrewing
the bolts (3) and (4) from the timing gear case cover
and the bolt (9) from the oil pan.
Notice: Be careful not to damage the oil pan gasket.
Installation Notice
Tightening Torque
Bolt (3, 4): 22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
Tightening Torque
Bolt (9):
9 -- 11 NSm
(80 -- 97 lb-in)
D
Apply the sealant after cleaning the timing gear
case cover surface.
D
Be careful not to stain the oil chamber of chain
tensioner with the sealant.
5. Installation should follow the removal procedure in
the reverse order.
6. Warm up the engine and check for oil leaks.
M162 ENGINE MECHANICAL 1B1 -- 33
DAEWOO MY_2000
CRANKSHAFT SEALING REAR COVER
Preceding Work: Removal of the automatic transmission drive plate
1 Bolt (M6 x 20, 6 pieces)
9--11 NSm (80--97 lb-in)
. . . . . . . . . . . . . . . . . . . . .
2 Radial Shaft Seal
3 Rear Cover
4 Sleeve
5 Bolt (M6 x 85, 2 pieces)
9--11 NSm (80--97 lb-in)
. . . . . . . . . . . . . . . . . . . . .
6 Washer
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст