SsangYong Korando II (1996-2006 year). Manual — part 88
M161 ENGINE MECHANICAL 1B2 -- 57
DAEWOO MY_2000
CAMSHAFT SPROCKET BOLT
Intake Flange Shaft Bolt
Tightening Torque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
Tightening Torque
2nd step: 60° ± 5°
Notice: The sprocket bolts are designed to be used only
once, so always replace with new one.
C. M7 x 13 Collar Bolt Torx--T30
e. 6.8 mm
16. Flange Shaft
18. Control Piston
22. Intake Camshaft
Exhaust Camshaft Sprocket Bolt
Tightening Torque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
Tightening Torque
2nd step: 60° ± 5°
Notice: The sprocket bolts are designed to be used only
once, so always replace with new one.
E. M7 x 13 Collar Bolt Torx--T30
e. 6.8 mm
13a. Camshaft Sprocket
22a. Exhaust Camshaft
1B2 -- 58 M161 ENGINE MECHANICAL
DAEWOO MY_2000
CAMSHAFT
Preceding Work: Removal of cylinder head cover
Removal of camshaft adjust actuator and cylinder head front cover
1 Bolt (M7 X 13, 3 pieces)
1st Step 18--22 NSm (13--16 lb-ft)
. . . . . . . . . .
2nd Step 60° ± 5° Rotation Added
2 Exhaust Camshaft Sprocket
3 Timing Chain
4a Intake Camshaft Spocket (E20)
4b Camshaft Adjuster and Camshaft
Sprocket (E23)
5 Bearing Cap Bolt (20 pieces)
22.5--27.5 NSm (16.6--20.3 lb-ft)
. . . . . . . . . . . . .
6 Camshaft Bearing Cap
7 Wrench
M161 ENGINE MECHANICAL 1B2 -- 59
DAEWOO MY_2000
Removal & Installation Procedure
1. Turn the crankshaft and position the no.1 cylinder pis-
ton at ATDC20°.
2. Put the alignment marks (arrows) on the camshaft
sprocket and the timing chain.
3. Remove the chain tensioner.
Installation Notice
Tightening
Screw Plug
40 NSm
(30 lb-ft)
Tightening
Torque
Tensioner
Assembly
72 -- 88 NSm
(53 -- 65 lb-ft)
4. Remove the exhaust camshaft sprocket.
Notice
Tightening Torque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
Tightening Torque
2nd step: 60° ± 5°
Notice: The sprocket bolt is designed to be used only
once, so always replace with new one.
5. Take off the timing chain from intake camshaft
sprocket, and secure it not to fall down into the timing
gear case.
6. Using the wrench (7), turn the camshaft until there is
no resistence in camshaft bearing area.
1B2 -- 60 M161 ENGINE MECHANICAL
DAEWOO MY_2000
7. Remove the bearing cap, and remove the intake
and the exhaust camshaft.
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
Notice: Check the numbers on the bearing cap not to be
mixed up.
8. Apply the engine oil on the valve tappet and cam-
shaft bearing.
9. Installation should follow the removal procedure in
the reverse order.
Notice:
D
Base circle of cam should cantact with the valve tap-
pet.
D
Install the camshaft bearing caps according to the
numbers on the cylinder head cast and bearing cap.
10. Check the camshaft timing position.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст