SsangYong Korando II (1996-2006 year). Manual — part 87
M161 ENGINE MECHANICAL 1B2 -- 53
DAEWOO MY_2000
Sectional View
1 Oil Pan
2 Cover
3 Radial Seal
4 Bolt
5 Crankshaft
6 Dowel Pin
7 Washer (Thickness : 3.5 mm)
8 Washer
9 Bolt
10 Front Drive Plate
11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear
1B2 -- 54 M161 ENGINE MECHANICAL
DAEWOO MY_2000
CAMSHAFT ADJUSTER
1 Bolt (M6 X 16, 3 pieces)
9--11 NSm (80--97 lb-in)
. . . . . . . . . . . . . . . . . . . .
2 Cylinder Head Front Cover
3 Bolt
35 NSm (26 lb-ft)
. . . . . . . . . . . . . . . . . . . . . .
4 Armature
5 Roll Pin
6 Nut (M20 X 1.5)
60--70 NSm (44--52 lb-ft)
. . . . .
7 Seal Cover
8 Camshaft Sprocket
9 Adjust Piston
10 Conical Spring
11 Flange Bolt (M7 X 13, 3 pieces)
1st Step 18--22 NSm (13--16 lb-ft)
. . . . . . . . . . .
2nd Step 60° ± 5° Rotation Added
12 Flange Shaft
13 Compression Spring
14 Control Piston
15 Circlip
16 Oil Gallery
17 Straight Pin
18 Intake Camshaft
Y49 Magnetic Actuator (2--pin connector)
M161 ENGINE MECHANICAL 1B2 -- 55
DAEWOO MY_2000
Removal & Installation Procedure
1. Turn the crankshaft and position the no.1 cylinder pis-
ton at ATDC 20°.
Notice: Turn the crankshaft in the direction of engine
rotation.
2. Remove the cylinder head front cover.
3. Put the alignment marks (arrows) on the camshaft
sprocket and the timing chain.
4. Insert the holding pin 111 589 03 15 00 into the no.1
and no.6 bearing cap hole on camshaft to secure in-
take and exhaust camshaft.
5. Remove the chain tensioner.
6. Unscrew the exhaust sprocket bolt and remove the
exhaust camshaft sprocket.
Installation Notice
Tightening Torque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
Tightening Torque
2nd step: 60° ± 5°
Notice: The flange bolt is designed to be used only
once, so always replace with new one.
1B2 -- 56 M161 ENGINE MECHANICAL
DAEWOO MY_2000
7. Unscrew the bolt (3) from the armature (4) and re-
move the roll pin, and remove the armature.
Installation Notice
Tightening Torque
35 NSm (26 lb-ft)
8. Unscrew the nut (6) and remove the seal cover (7).
Installation Notice
Tightening Torque
60 -- 70 NSm (44 -- 52 lb-ft)
Notice: Put the locking slot of nut toward armarture.
9. Take off the timing chain from intake camshaft
sprocket.
10. Remove the adjuster piston (9) and conical spring
(10) from intake camshaft sprocket.
11. Unscrew the bolt (11) and remove the flange shaft.
Installation Notice
Tightening Torque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
Tightening Torque
2nd step: 60° ± 5°
Notice: The flange bolt is designed to be used only
once, so always replace with new one.
12. Installation should follow the removal procedure in
the reverse order.
13. Check and adjust the camshaft timing.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст