SsangYong Korando II (1996-2006 year). Manual — part 21
1B1 -- 50 M162 ENGINE MECHANICAL
DAEWOO MY_2000
CAMSHAFT ADJUSTER
Preceding Work: Removal of cylinder head cover
Removal of cylinder head front cover
1 Bolt (M6 x 16, 3 pieces)
9--11 NSm (80--97 lb-in)
. . . . . . . . . . . . . . . . . . . . .
2 Magnet Assembly (2 Pin Connector)
3 Bolt
35 NSm (26 lb-ft)
. . . . . . . . . . . . . . . . . . . . . .
4 Armature
5 Roll Pin
6 Nut (M20 x 1.5)
60--70 NSm (44--52 lb-ft)
. . . . . .
7 Front Cover
8 Seal
9 Camshaft Position Sensor
10 Bolt (M6 x 16, 2 pieces)
9--11 NSm (80--97 lb-in)
. . . . . . . . . . . . . . . . . . . . .
11 Seal
12 Seal Cover
13 Camshaft Sprocket and Position Indicator (b)
14 Adjuster Piston
15 Flange bolt (M7 x 13, 3 pieces)
1st step 18--22 NSm (13--16 lb-ft)
. . . . . . . . . . .
2nd step 60° ± 5°
16 Flange Shaft
17 Compression Spring
18 Control Piston
19 Circlip
20 Oil Gallery
21 Pin
22 Intake Camshaft
M162 ENGINE MECHANICAL 1B1 -- 51
DAEWOO MY_2000
Removal & Installation Procedure
1. Turn the crankshaft to the direction of engine rotation
and position the no.1 cylinder piston at TDC which the
camshaft is positioned at OT.
2. Remove the cylinder head front cover.
3. Paint the alignment marks (arrows) on the intake and
exhaust camshaft sprocket and the timing chain.
3 Bolt
13 Camshaft Sprocket
4 Amarture
18 Control Piston
6 Nut (M20 x 1.5)
22 Intake Camshaft
12 Seal Cover
4. Unscrew the bolt (3) from the armature (4) and re-
move the armature.
Installation Notice
Tightening Torque
35 NSm (26 lb-ft)
5. Unscrew the nut (6) and remove the ring and seal
cover (11).
Installation Notice
Tightening Torque
60 -- 70 NSm (44 -- 52 lb-ft)
6. Unscrew the sprocket bolt from the exhaust camshaft
and remove the sprocket.
Installation Notice
Tightening Torque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
Tightening Torque
2nd step: 60° ± 5°
The sprocket bolt is designed to be used only once,
so always replace with new one.
1B1 -- 52 M162 ENGINE MECHANICAL
DAEWOO MY_2000
7. Remove the camshaft sprocket (13) and adjust piston
(14), and remove the flange shaft (16) from the intake
camshaft (22) after removing the bolt (15).
Installation Notice
Tightening Torque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
Tightening Torque
2nd step: 60° ± 5°
The sprocket bolt is designed to be used only once,
so always replace with new one.
8. Installation should follow the removal procedure in
the reverse order.
9. Adjust the camshaft timing.
CAMSHAFT SPROCKET BOLT
Intake Flange Shaft Bolt
Tightening Torque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
Tightening Torque
2nd step: 60° ± 5°
Notice: The sprocket bolts are designed to be used only
once, so always replace with new one.
C. M7 x 13 Collar Bolt Torx--T30
e. 6.8 mm
16. Flange Shaft
18. Control Piston
22. Intake Camshaft
M162 ENGINE MECHANICAL 1B1 -- 53
DAEWOO MY_2000
Exhaust Camshaft Sprocket Bolt
Tightening Torque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
Tightening Torque
2nd step: 60° ± 5°
Notice: The sprocket bolts are designed to be used only
once, so always replace with new one.
E. M7 x 13 Collar Bolt Torx--T30
e. 6.8 mm
13a. Camshaft Sprocket
22a. Exhaust Camshaft
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст