SsangYong Korando II (1996-2006 year). Manual — part 374
SSANGYONG MY2002
6E-8 POWER STEERING AND COLUMN
Check the ignition switch for damage.
Check the ignition switch for improper installation.
Check the ignition switch electrical connector for
improper installation.
Checks
Action
Replace the ignition switch.
Remove and inspect the ignition switch. Reinstall the
ignition switch.
Reconnect the ignition switch electrical connector.
Replace the ignition switch electrical connector.
Ignition Switch Will Not Turn
Wiper/Cruise Control Switch Lever
Switch Inoperative: No LOW, HIGH, INTERMITTENT or WASH
Check the wiper switch for damage.
Check the wiper switch for improper installation.
Check the cruise control switch for damage.
Checks
Action
Replace the wiper/cruise control switch.
Remove and inspect the wiper/cruise control switch.
Reinstall the wiper/cruise control switch.
Replace the wiper/cruise control switch.
Ignition Switch
Electrical System Will Not Function
Check the ignition switch for damage.
Check the ignition switch for improper installation.
Checks
Action
Replace the ignition switch.
Remove and inspect the ignition switch. Reinstall the
ignition switch.
POWER STEERING AND COLUMN 6E-9
SSANGYONG MY2002
KAA6E060
KAA6E040
ON-VEHICLE SERVICE
HEADLAMP/TURN SIGNAL
SWITCH AND LEVER
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the upper and the lower steering column
cover screws.
3. Remove the upper and the lower steering column
cover.
REPAIR INSTRUCTIONS
KAA6E050
4. Remove the turn signal switch mounting screws.
5. Disconnect the turn signal switch connector.
6. Remove the turn signal switch.
SSANGYONG MY2002
6E-10 POWER STEERING AND COLUMN
KAA6E060
KAA6E080
KAA6E070
WIPER SWITCH AND LEVER
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the upper and the lower steering column
cover screws.
3. Remove the upper and the lower steering column
cover.
4. Remove the wiper switch and lever mounting
mounting screws.
Tightening Torque
65 N•m (48 lb-ft)
5. Disconnect the wiper switch and lever connector.
6. Remove the wiper switch and lever.
STEERING WHEEL WITH SIR
Tools Required
661 589 00 33 00 Steering Wheel Puller
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the SIR module. Refer to Section 8B, Sup-
plemental Inflatable Restraints.
3. Remove the steering wheel nut.
Removal Notice:
•
In order to install the steering wheel correctly,
match mark the steering column shaft to the
steering wheel.
Installation Notice
POWER STEERING AND COLUMN 6E-11
SSANGYONG MY2002
KAA6E040
KAA6E100
KAA6E090
4. Remove the steering wheel using the steering
wheel puller 661 589 00 33 00.
Installation Notice:
•
Align the match marks on the steering wheel
and the steering column shaft.
IGNITION LOCK CYLINDER AND
SWITCH
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the upper and the lower steering column
cover screws.
3. Remove the upper and the lower steering column
cover.
4. Remove the screws for illumination keyhole
connection.
5. With the key in the ignition turned to the position
designated ACC, remove the lock cylinder by
pressing down the detent spring with a 2.5 mm
allen wrench or other suitable tool, and pulling the
lock cylinder out of the cylinder housing.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст