SsangYong Korando II (1996-2006 year). Manual — part 320
AUTOMATIC TRANSMISSION 5A-183
SSANGYONG MY2002
C3 Clutch and Reverse Sun Gear Assembly
Tools Required
0555-336259 Clutch Spring Compressor
0555-336260 Clutch Pack Clearance Kit
1. Check the orifices in the cylinder are clear of ob-
structions.
2. Check the C3 cylinder bush outside diameter and
the centre support inside diameter are in good
condition and not damaged. Coat the sealing rings
with automatic transmission fluid and fit into the
C3 cylinder grooves.
3. Check the reverse sun gear splines, grooves and
thrust face for condition. Coat the ‘O’ ring with
automatic transmission fluid and fit it to the groove
of the reverse sun gear.
4. Lubricate the C3 washer with petroleum jelly and
fit to the inner face of the reverse sun gear.
5. Install the reverse sun gear in the C3 cylinder,
e n s u r i n g t h a t t h e ‘ O ’ r i n g c o m p r e s s i o n i s
adequate but not excessive.
Notice: ‘O’ rings must not be twisted in the
grooves.
KAA5A0P0
6. Coat the C3 piston ‘O’ rings with automatic trans-
mission fluid and fit the small ‘O’ ring onto the
inner ring and the large ‘O’ ring onto the outer
ring of the C3 piston.
7. Check that the bleed orifices of the piston are
clean and clear of obstructions.
8. Install the C3 piston in the cylinder until the
outside diameter of the piston enters the inside
diameter of the cylinder.
Notice: Take care not to cut the ‘O’ ring.
9. Assemble the spring and spring retainer on the
p i s t o n . U s i n g 0 5 5 5 - 3 3 6 2 5 9 c l u t c h s p r i n g
compressor compress the spring sufficiently to
enable the installation of the retaining circlip,
ensuring that the circlip is firmly seated in the
groove, and remove the tool.
10. Fit the C3 wave plate to the C3 piston face,
ensuring that one crest of the wave plate of the
C3 piston face is aligned over one of the piston
orifices.
KAA5A0Q0
KAA5A730
5A-184 AUTOMATIC TRANSMISSION
SSANGYONG MY2002
11. Assemble the clutch plates and discs into the
cylinder in the following sequence :
•
Steel plate
•
Friction disc
•
Steel plate
•
Steel plate (0574-000013, `014, `015, `016, `019,
`022), or Friction disc (0574-000012, `017)
•
Steel plate (selective)
•
Friction disc
•
Steel plate (selective)
•
Friction disc
12. A l i g n a n d f i t t h e p r e s s u r e p l a t e w i t h t h e
counterbore facing away from the clutch plates.
13. Install the circlip.
14. Check the C3 clutch clearance using 0555-336260
clutch pack clearance kit in the following manner
(weight only).
a. Place the weight on the pressure plate and
measure the distance from the end of the
cylinder to the top of the pressure plate.
b. Record this figure.
c. Remove the weight.
d. Lift the pressure plate up against the circlip
and measure the distance from the end of the
cylinder to the top of the pressure plate.
e. Record this figure.
f. Subtract the second reading from the first read-
ing to obtain the clutch pack clearance.
KAA5A0R0
KAA5A0S0
AUTOMATIC TRANSMISSION 5A-185
SSANGYONG MY2002
Notice: With the clutch pack supporting a weight
of 2kg, the clearance between the snap ring and
the top of the pressure plate is to be between 1.07
- 1.45 mm.
15. If new friction plates are being fitted, remove the
clutch pack and soak the friction elements in auto-
matic transmission fluid for a minimum of five min-
utes prior to reassembly.
Notice: The clutch pack clearance must be taken
before the elements are soaked in automatic
transmission fluid.
Forward Sun Gear and C3 Clutch Pack
Assembly
1. Fit the No. 7 needle bearing assembly over the
for-ward sun gear, ensuring that the thrust washer
is between the bearing and the sun gear.
2. Lubricate the lipped thrust plate with petroleum
jelly and fit the thrust plate onto the reverse sun
gear.
KAA5A0U0
KAA5AOTA
3. Align and fit the C3 clutch assembly over the for-
ward sun gear.
4. Lubricate the No. 6 needle bearing with petroleum
jelly and fit it to the thrust plate. Ensure the lugs
on the outside diameter of the bearing fit in the
thrust plate counterbore.
5. Align and fit the plastic thrust washer to the thrust
plate with petroleum jelly.
6. Install the assembly over the forward sun gear
shaft against the No. 6 needle bearing.
7. Place the assembly to one side.
KAA5A0W0
KAA5A0V0
5A-186 AUTOMATIC TRANSMISSION
SSANGYONG MY2002
KAA5A0X0
C1 Clutch Overdrive Shaft and Input Shaft
Assembly
Tools Required
0555-336260 Clutch Pack Clearance Kit
Notice:
•
Ensure that the snap rings are fitted correctly.
•
Check pistons for cracks, especially the C1 piston.
•
Do not mix clutch piston return springs.
•
If the C1/C2 clutch packs separate from the C3
clutch pack, make sure the No. 6 bearing doesn’t
drop out of the bearing retainer.
1. Check the overdrive shaft grooves for any defect.
2. Coat the sealing rings, large and small, with petro-
leum jelly and fit them to the overdrive shaft. The
sealing rings may be held in place with a small
amount of petroleum jelly.
3. Assemble the clutch plate and disc into the cylinder
in the following sequence:
•
Steel plate
•
Friction disc
•
Steel plate
•
Friction disc
•
Steel plate
•
Steel plate ( 0574-000013, `014, `015, `016, `019,
`022), or friction disc (0574-000012 & `017)
•
Steel plate (selective)
•
Friction disc
•
Steel plate (selective)
•
Friction disc
4. Check the clutch pack clearance using 0555-
336260 clutch pack clearance kit.
5. Use selective plates to achieve the correct
specification.
Notice: With the clutch pack supporting a 2 kg
weight, the dimension from the input shaft locating
stop to the friction disc must be 0.70 - 0.90 mm.
6. If new friction plates are being fitted, remove the
clutch pack and soak the friction elements in auto-
matic transmission fluid for a minimum of five
minutes prior to assembly.
Notice: The clutch pack clearance must be taken
before elements are soaked in automatic
transmission fluid.
KAA5A0X0
KAA5A0Y0
KAA5A0Z0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст