SsangYong Musso. Manual — part 303
1D2-10 M161 ENGINE COOLING
Tools Required
124 589 15 21 00 Tester
Removal & Installation Procedure
1. Drain the coolant.
2. Disconnect the coolant hoses (8, 9, 10).
3. Tak off the drive belt.
4. Unscrew the four bolts (6) from coolant pump pulley and
remove the pulley (7).
Installation Notice
Tightening Torque
9 - 11 Nm
22.5 - 27.5 Nm
(1, 2, 3)
(4)
Notice
Hold the pulley with special tool (603 589 00 40 00) while
removing the pulley.
Tightening Torque
9 - 11 Nm
5. Unscrew the bolts (1, 2, 3, 4) from coolant pump housing
(5) and remove the coolant pump.
Installation Notice
6. Clean the sealing surface.
7. Replace the gasket with new one.
Notice
Apply the sealant when the sealing surface of coolant pump
housing and coolant mounting area is clean.
8. Installation should follow the removal procedure in the
reverse order.
9. Check for leaks by starting the engine.
M161 ENGINE COOLING 1D2-11
THERMOSTAT
Removal & Installation Procedure
1. Drain the coolant from the radiator.
2. Loosen the hose mounting clip and remove the coolant hose
(3, 4).
3. Unscrew the three bolts (1) and remove the thermostat cover
assembly from thermostat housing.
Installation Notice
Do not separate the thermostat cover and thermostat.
4. Replace the O-ring if necessary.
5. Check the leakage in the cooling system.
Tightening Torque
9 - 11 Nm
1 Bolt (M6 X 25, 3 pieces) . . . . . . 9 -11 Nm
2 Thermostat Cover
3 De-aeration Hose
4 Coolant Outlet Hose
5 Thermostat
6 O-ring
1D2-12 M161 ENGINE COOLING
THERMOSTAT HOUSING ASSEMBLY
Preceding Work : Removal of viscous clutch
1a Bolt (M6 X 95, 2 pieces) . . . . . . . 9-11 Nm
1b Bolt (M8 X 75, 2 pieces) . . . . . 22.5-27.5 Nm
1c Bolt (M8 X 35, 1 piece) . . . . ... 22.5-27.5 Nm
2 Thermostat Housing Assembly
3 O-ring
4 De-aeration Hose
5 Coolant Outlet Hose
6 Coolant Bypass Hose
7 Tensioning Device Shock Absorber
8 Engine Hanger Brocket
M161 ENGINE COOLING 1D2-13
Removal & Installation Procedure
1. Drain the coolant.
2. Remove the de-aeration hose (4), coolant outlet hose (5)
and coolant bypass hose (6).
3. Disconnect the coolant temperature sensor connector.
4. Unscrew the bolt (1c) and pry off the tensioning device shock
absorber (7).
Installation Notice
6. Replace the O-ring with new one.
7. Installation should follow the removal procedure in the
reverse order.
8. Check for leaks in cooling system.
5. Unscrow the bolts (1a, 1b) and remove the engine
hanger bracket and thermostat housing.
Installation Notice
Tightening Torque
9 - 11 Nm
22.5 - 27.5 Nm
(1a)
(1b)
Tightening Torque
22.5 - 27.5 Nm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст