SsangYong Musso. Manual — part 353
M162 ENGINE INTAKE & EXHAUST 1G1-11
Removal and Installation of Exhaust Line
1 Exhaust Manifold
2 Rivet Nut
3 Bolt . . . . . . . . . . . . . . ... 30 Nm
4 Front Pipe
5 Oxygen Sensor
6 Bolt . . . . . . . . . . . . . .. 28-47 Nm
7 Rubber Pad
8 Catalytic Converter
9 Gasket . . . . . . . . . . . . ... Replace
10 Nut
11 Gasket . . . . . . . . . . . . ... Replace
12 Rubber Pad
13 Nut . . . . . . . . . . . . . ... 28-47 Nm
14 Center Muffler
15 Rubber Pad
16 Tail Muffler
17 Gasket . . . . . . . . . . . . ... Replace
18 Nut . . . . . . . . . . . . . ... 28-47 Nm
SECTION 1G2
M161 ENGINE INTAKE & EXHAUST
TABLE OF CONTENTS
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
N
z
z
z
z
z
m
9 - 11
22.5 - 27.5
22.5 - 27.5
9.5 - 12.5
15 - 28
28 - 47
Application
Air Cleaner Housing Cover Nut
Intake Manifold Bolt (M8 x 20)
Intake Manifold Bolt (M8)
Exhaust Mainfold Stud Bolt
Exhaust Pipe Nut (Engine)
Exhaust Pipe Bolt
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1G2-1
Fastener Tightening Specifications . . . . . . . . 1G2-1
Maintenance and Repair . . . . . . . . . . . . . . 1G2-2
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1G2-2
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 1G2-2
Air Intake Shield . . . . . . . . . . . . . . . . . . . . . . 1G2-4
Intake Air Duct . . . . . . . . . . . . . . . . . . . . . . . 1G2-5
Intake Manifold . . . . . . . . . . . . . . . . . . . . . . . 1G2-7
Exhaust Manifold . . . . . . . . . . . . . . . . . . . . . 1G2-9
1G2-2 M161 ENGINE INTAKE & EXHAUST
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
AIR CLEANER
1 Air Cleaner Assembly
2 Element Assembly
3 Insulator
4 Air Duct Hose
5 Air Inlet Duct
6 Bolt (M8 × 30 ) . . . . . . . . ... 22.5-27.5 Nm
7
Bolt (M6 × 35 ) . . . . . . . . . . ... 9-11 Nm
M161 ENGINE INTAKE & EXHAUST 1G2-3
Removal & Installation Procedure
1. Release the clamp securing HFM sensor and air cleaner.
2. Disengage the air cleaner assembly and HFM sensor
assembly.
3. Unserew the mounting bolt(6) from the bracket.
Installation Notice
Tightening Torque
22.5 - 27.5 Nm
4. Release the clamp from air cleaner assembly housing and
remove the cover.
5. Remove the air cleaner assembly.
6. Remove the air cleaner housing from insulator.
Notice
Make sure the air cleaner to be seated in insulator.
7. Disengage the air duct hose and air cleaner housing and
remove the housing.
8. Remove the air duct hose.
9. Unscrew the two bolts(7) from air inlet duct.
Installation Notice
10. Remove the air inlet duct.
11. Installation should follow the removal procedure in the
reverse order.
Tightening Torque
8 - 9 Nm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст