SsangYong Stavic / SsangYong Rodius (2005 year). Manual — part 11
1B-23
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
CYLINDER HEAD COVER
1. Ignition cable dust cover
2. Bolt (M6 x 65, 8 pieces) . 9 ~ 11 Nm (80 ~ 97 lb-in)
3. Bolt (M6 x 50, 4 pieces) . 9 ~ 11 Nm (80 ~ 97 lb-in)
4. Spacer sleeve
5. Thrust piece
6. Cylinder head cover
7. Gasket . . . . . . . . . . . . . . .. Replace
8. Spart plug hole seal . . . . . . . . . . Replace
9. Camshaft seal . . . . . . . . . . . .. Replace
Composition of The Cylinder Head
Cover Bolts
A. M6 x 50, 4 Pieces - Bolts + Washers
B. M6 x 65, 8 Pieces - Bolts + Washers
1B-24
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
2. Remove the spark plug cover.
Installation Notice
4. Unscrew all the bolts (2, 3) and remove the head cover
and the gasket.
Installation Notice
3. Remove the spark plug connector and ignition cable.
Removal & Installation Procedure
1. Remove the intake air duct.
Installation Notice
Unscrew the seven (M6 x 60) bolts and remove the spark
plug cover.
Tightening torque
9 ~ 11 Nm
(80 ~ 97 lb-in)
Tightening torque
9 ~ 11 Nm
(80 ~ 97 lb-in)
Replace the gasket with a new one if necessary.
5. Installation should follow the removal procedure in the
reverse order.
6. Check for oil leaks by operating the engine.
Tightening torque
9 ~ 11 Nm
(80 ~ 97 lb-in)
1B-25
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
Removal & Installation Procedure
1. Remove the camshaft actuator.
Installation Notice
CYLINDER HEAD FRONT COVER
Preceding Work: Removal of cylinder head cover
Removal of coolant connection fitting
1. Camshaft position sensor
2. Camshaft actuator
3. Upper guide rail
4. Bolt (M6 x 60, 3 pieces)
. . . . . . . 22.5 ~ 27.5 Nm (16.6 ~ 20.3 lb-ft)
5. Bolt (M8 x 80, 3 pieces)
. . . . . . . 22.5 ~ 27.5 Nm (16.6 ~ 20.3 lb-ft)
6. Front cover
7. Rubber gasket . . . . . . . . . . . .. Replace
8. Bolt (M6 x 16, 3 pieces)
. . . . . . . . . . .. 9 ~ 11 Nm (80 ~ 97 lb-in)
Tightening torque
9 ~ 11 Nm
(80 ~ 97 lb-in)
1B-26
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
4. Remove the gasket (arrow).
Notice
Replace the gasket with new one and apply the
sealant.
5. Installation should follow the removal procedure in the
reverse order.
2. Remove the cylinder head front cover (6).
Installation Notice
Apply the sealant at the mating surface of the cylinder
head and the front cover.
3. Remove the upper guide rail pin and the guide rail (3).
Notice
Install it while the chain tensioner is loose.
Tightening torque
22.5 ~ 27.5 Nm
(16.6 ~ 20.3 lb-ft)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст