SsangYong Stavic / SsangYong Rodius (2005 year). Manual — part 27
1B-92
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
Capacity
Quality
Viscosity
Replacemant
Application
ENGINE OIL SPECIFICATION
1. Drain plug . . . . . . . . . 25 Nm (18 lb-ft)
2. Oil filter
3. Engine oil filler cap
4. Dipstick gauge
Specifications
LUBRICATION SYSTEM
Min: 7.0L, Max: 9.0L
• API SH or above grade
• ACEA: A2 or A3
• Approved oil by MB Sheet 229.1
• Approved oil by MB Sheet 224.1
• Initial at 1000 ~ 1500 km, Replace every 15000 km
Descrition
1B-93
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
REPLACEMENT
1. Install the socket wrench A9910 0050A (103 589 02 09
00) on the oil filter cover (2).
Notice
Tighten the bolts on the socket wrench to remove
the screw cover.
2. Set a wrench on the bolt on the top of socket wrench
and turn it to remove the oil filter cover.
3. Remove the oil filter element.
Notice
Wrap the used filter element with a shop cloth so
that the oil cannot drop on the floor.
4. Remove the drain plug (1) and drain the engine oil
completely.
Notice
To drain the oil easily, remove the oil filler cap (3).
5. Clean the drain plug and reinstall it.
Installation
Tightening torque
25 Nm
9. Pour the engine oil through the engine oil filler hole.
10. Run the engine and check for oil leakage at normal
operating temperature.
11. Stop the engine and wait for 5 minutes. Check the oil
level and add if necessary.
Tightening torque
25 Nm
Notice
Replace the seal washer with new one.
6. Replace the O-ring (5) on the oil filter cover with new
one.
Notice
When replacing, apply the engine oil on the O-ring.
7. Insert new oil filter element into the oil filter housing.
8. Temporarily tighten the oil filter cover (2) by hands and
then tighten it with the socket wrench A9910 0050A
(103 589 02 09 00).
Installation
1B-94
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
1. Oil pump
2. Oil gallery (to oil filter)
3. Oil filter
4. Oil pressure switch
5. Main oil gallery
6. Cylinder head closing cover
7. Oil gallery (at chain tensioner)
8. Oil non-return valve
9. Chain tensioner
10. Vent (chain tensioner)
11. Front closing cover (
φ 17 mm)
12. Oil gallery (perpendicular to the shaft)
13. Ball (
φ 6 mm)
14. Oil spray nozzle (timing chain)
15. Oil gallery (at cylinder head)
16. Ball (
φ 15mm)
17. Oil restriction inner (
φ 4mm)
18. Oil supply (to exhaust camshaft)
OIL CIRCULATION
19. Oil supply (to intake camshaft)
20. Oil supply (to exhaust camshaft bearing)
21. Oil supply (to intake camshaft bearing)
22. Oil gallery (oil supply to exhaust valve tappet)
23. Oil gallery (oil supply to intake valve tappet)
24. Camshaft closing cover
25. Ball (
φ 8 mm)
26. Screw plug
27. Camshaft adjuster
28. Front closing cover (intake camshaft)
29. Front treaded bushing (exhaust camshaft)
30. Valve tappet
a. Oil gallery (from oil pump to oil filter)
b. Main oil gallery
c . Oil return line (oil returns to the oil pan when
replacing the filter element)
1B-95
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
4. Remove the drain plug (1) and drain the engine oil.
Notice
Leave the oil filler cap open to ease the engine oil
discharge.
5. Tighten the engine oil drain plug after cleaning it.
Installation Notice
ENGINE OIL AND OIL FILTER ELEMENT
Tools Required
A9910 0050A (103 589 02 09 00)
Oil Filter Remover
Replacement Procedure
1. Install the oil filter remover A9910 0050A (103 589 02 09
00) on the oil filter cover.
Notice
Make the screw cover removable by tightening the
bolt at the side of the oil filter remover A9910 0050A
(103 589 02 09 00).
2. Install the wrench to the upper bolt in the oil filter remover
A9910 0050A (103 589 02 09 00) and remove the oil cover
by turning it.
3. Remove the oil filter element.
Notice
Work with a cloth under the vehicle when removing
the oil filter element to not drain the oil.
Replace the seal washer with new one.
6. Replace the O-ring in the oil filter cover with new one.
Notice
Apply the engine oil to the O-ring.
7. Insert new oil filter element into the oil filter housing.
8. Temporarily tighten the oil filter cover. Install the oil filter
remover A9910 0050A (103 589 02 09 00), and then
completely tighten it.
Installation Notice
Tightening torque
25 Nm (18 lb-ft)
Tightening torque
25 Nm (18 lb-ft)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст