SsangYong Rexton. Manual — part 651
GENERAL BODY 9A-7
SSANGYONG Y200
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
;;;;;;;;;;;;;
REPAIR
Repair Leaking Water
Leaking water on the section of glass can be repaired
without removal of glass.
Notice: Method to repair of following description is
applied on the equipped glass of urethane sealing.
1. Remove leaking moulding and section of trim, to
detect position of leaking water it is necessary for
technician to remove trim and garnish moulding
2. During injecting water on the leaking section, to
detect quantity of leaking water, carefully push
the glass external area.
3. Mark accurate position of leaking water.
4. Wash section of leaking water and dry up air hose.
YAD9A090
YAD9A100
5. Remove ununiform section of cohesive material
on the distance of 75 - 100 mm to leaking section
6. Spread prima on the uniform section leaking
SSANGYONG Y200
9A-8 GENERAL BODY
YAD9A110
Method to Repair Wind Noise
Method to repair wind noise is similar to method to
repair leaking water.
Wind noise of around door opening weather strip is
not proper installed.
Weather but depends on adjusting door and window.
Method to Repair Body Noise
Due to not properly installed parts of body, body noise
is occurred, in order not to make a noise, proceed the
following description.
•
Install completely relative moving parts under
vehicle’s moving.
•
Repair clearance of moving parts under vehicle’s
moving.
•
In order not to cause body noise about moving
parts, separate, moving parts, treat soundproof.
•
Uniform surface of friction can prevent harding
state.
7. Wait approximately 5 minutes, until drying up
prima.
8. Spread cohisive material on the distance of 75 -
100 mm to leaking section.
9. After spreading cohisive material, using the flat
stick and similar equipment, keep body and
cohisive material uniform in order not to leak water.
10. To make sure to finish repairing leaking water,
inject warm water or, hot water on the section of
leaking water.
11. Install parts removed to repair leaking section.
Notice: After repairing section of leaking water
completely, using stand for leaking. test, check
the section of leaking water again, if abnormal
pressure is checked, repaired cohesive material
may get out of position itself. So leaking water
test should not check on local section of leaking .
GENERAL BODY 9A-9
SSANGYONG Y200
SPECIAL TOOLS AND EQUIPMENT
SPECIAL TOOLS TABLE
09861- 31200
Cuttibg Knife of Sealant
09861-31400
Glass Holder
09793-21000
Adjusting Wrench of
Door Wrench
09853-31000
Remover of Headlning
Clip
09861-31300
Sealant Gun
09861-31000
Remover of Wind Shield
Molding
09800-21000
Ornament Remover
09861-31100
Cutting Tool of Sealant
YAD9A120
YAD9A130
YAD9A140
YAD9A150
YAD9A160
YAD9A170
YAD9A180
YAD9A190
SECTION 9B
BODY INTERIOR
TABLE OF CONTENTS
Components Location . . . . . . . . . . . 9B-2
Instrument Assembly . . . . . . . . . . ... 9B-2
Side Trim and Roof Assembly . . . . . . . .. 9B-3
Seat . . . . . . . . . . . . . . . . . 9B-4
Console . . . . . . . . . . . . . . . ... 9B-5
Removal and Installation . . . . . . . . . . 9B-6
Instrument . . . . . . . . . . . . . . ... 9B-6
Console Box . . . . . . . . . . . . . . 9B-9
Groove Box . . . . . . . . . . . . . ... 9B-10
Trim and Roof . . . . . . . . . . . . . 9B-10
Handler . . . . . . . . . . . . . . . . 9B-15
Sunvisor . . . . . . . . . . . . . . . 9B-15
Room Miror . . . . . . . . . . . . . . 9B-15
Seat . . . . . . . . . . . . . . . . .. 9B-16
Removal and Installation . . . . . . . . ... 9B-18
Front Seat . . . . . . . . . . . . . . .. 9B-18
Two Row Seat . . . . . . . . . . . . . 9B-19
Seat of Three Row . . . . . . . . . . . .. 9B-20
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст