SsangYong Rexton. Manual — part 650
GENERAL BODY 9A-3
SSANGYONG Y200
DIGNOSIS AND ACTION TAKEN
DIAGNOSIS FOR LEAKING
WATER
It is required for technician to inspect and diagnose
accurately problems of leaking water.
Problem of leaking water is repaired by adjusting of
misaligned parts by using proper equipment, first of
all check condition of leaking water.
For example, condition caused leaking water to occur
should be checked if vehicle is parked on the sloping
road or spare tire in the trunk.
Next step of checking leaking section of water is
following as belows. If general leaking section of water
is detected, check accurate leaking section of water,
by using water hose or air hose. If general leaking
section of water is not detected, check leaking section
of water, by using the stand of tester of leaking water.
It is required for technician to check accurate leaking
section of water such as, removal of internal trim panel
or component parts .
Notice: Technician should detect cause of leaking
water before leaking section of water is repaired.
It is difficult for technician to do temporary solution of
leaking water, but also this one will cause more difficult
situation to solve problem of leaking water.
To ensure detecting leaking section of water, keep test
for leaking section of water.
Adjust weather strip
Adjust and replace weather strip
Adjust
Adjust
Adjust
Repair or replace
1) Remove abnormal material from drain hose or pipe
2) Abnormal material is removed from drain hose or
pipe by compressor
3) Check the state of installing and connecting section
in the drain hose or pipe
4) Replace
5) Adjust
1) Retighten or replace
1) Adjust the position
2) Replace
3) Replace
1) Adjust position
2) Replace
3) Repair or replace
4) Grease
1) Adjust
2) Adjust
3) Adjust
Spread sealant
Repair
1) Not installed weather strip tightly
2) Misinstalled of weather strip
3) Not closed door accurately
4) Misinstalled or door
5) Not keep constant clearance
between door glass and moulding
6) Deformed of door
1) Abnormal material build up on drain
hose and pipe
2) Drain hose or pipe is clogged up
3) Misinstalled of drain hose or pipe,
deformed or broken clip
4) Deformed weather strip of roof-lid
5) Not keep clearance constant
between roof-lid and body or mis
Installed weather strip
1) Loose or deformed deflector
1) Misinstall of wind glass
2) Failure of motor
3) Failure of power window switch
1) Misinstalled of door
2) Misoperated of door lock
3) Deformed of door checker
4) Lack of grease at door hinge
1) Not fitted the position between
striker and latch
2) Misinstalled of hood
3) Inproper height of hood bumper
Lack of sealing
Damaged flange
Cause
Action Taken
Wind noise
around door
Leaking water
from sun roof
Wind noise
around sun
roof
Failure of door
glass
Not closed
door or not
opened
completely.
Not closed
hood or not
opened
completely.
Leak from
windshield or
rear window
SSANGYONG Y200
9A-4 GENERAL BODY
CHECK
General Checking Leaking Water
1. Install checking equipment
2. Check leaking water.
3. If water pressure is getting below regulated water
pressure, to inject water overlapping, technician
keeps vehicle close to stand of each side.
YAD9A010
YAD9A020
YAD9A030
Check Local Section of Leaking Water
1. Test local section of leaking water by using water
hose or air hose
2. First of all, test dubious section of leaking water
by injecting water or air, until technician detect
section of leaking water, point of checking is
moving from the low of vehicle to the upper of
vehicle.
Check the Water Hose
1. In order to detect section of leaking water, another
technician, is moving into the internal of vehicle.
2. Use water hose not having a nozzle.
3. First of all, test dubious section of leaking water
by injecting water or air,until technician detect
section of leaking water, point of checking is
moving from the low of vehicle to the upper of
vehicle.
CHECK AND REPAIR
GENERAL BODY 9A-5
SSANGYONG Y200
Dignosis of Wind Noise
Notice: If technician diagnose the vehicle wind noise,
another technician is driving the diagnosed vehicle for
the prevention of vehicle unsafe.
It is necessary for technician to drive vehicle in order
to analyse position of wind noise, accurately, wind
noise is occurred by first leaking and second, if all the
leaking section is not repaired, wind noise will be
reduced little bit, but wind noise will not be reduced
completely
For technician to diagnose position of wind nose with
driving test, following description should be provided
•
vacuum hose
•
vinyl tape
•
scrip cork
•
pencil indicating
•
screw driver
Driving test should be observed as followings.
1. Select straight and even road which is available
to East,West,South, and North.
2. Select road not preventing test which has no noise
or traffic obstacle.
3. Drive the vehicle when wind noise is occurred
Keep in mind within specified vehicle speed.
4. If following condition happen, each one is defined,
as external wind noise.
•
wind noise is occurred by wind
•
wind noise happen on the lower side of door
glass under vehicle is driving
•
wind noise is removed by taping of moulding
Check Air Hose
1. Soap bubbles is fed on the dubious section of
leaking water.
2. Inject air from the internal of the vehicle, not to
keep compressing air, over 205 kPa ( 29.7 psi ).
3. Check whether bubble of soap is occurred on the
dubious section of leaking water, or not and then
make sure section of leaking water.
YAD9A040
SSANGYONG Y200
9A-6 GENERAL BODY
5. Internal wind noise is repaired following description
•
L e a k i n g s e c t i o n i s d e t e c t e d b y u s i n g
stethoscope or vacuum hose is repaired by
using vinyl tape temporarily.
•
Keep driving test to check whether wind noise
is removed or not if leaking section is checked.
•
Wind noise will be completely repaired by
proper equipment, tool of sealing.
YAD9A0650
YAD9A060
Body
Periodically hood and locking system should be fed
for operating smoothly, specially feeding oil to the
section of closing and opening is depending on
operation smooth and prevention of noise.
YAD9A070
Bolt and Nut
Notice: Contacting surface to the non-characteristic
of each metal cause each metal to corrode so, for
prevention of early corrosion, use specified bolt and
nut
Alloy of aluminium is using currently most vehicle
Contacting between steel and aluminium cause to
corrode if those are ,not hardening.
Special bolt and nut are using for prevention of
corrosion in the vehicle.
If bolt and nut are replaced, same specification of bolt
and nut should be, used or similar material of bolt and
nut.
YAD9A080
The Prevention of Corrosion
In order not to corrode body, surface of internal panels
of metal is added, material of anti-corrosion. If those
panel are replaced, spread material of anti- corrosion
on the panels with proper quantity
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст