SsangYong Rexton. Manual — part 305
M162 ENGINE MECHANICAL 1B1-23
SSANGYONG Y200
Removal and Installation Procedure
1. Unscrew the upper engine mounting nut.
Installation Notice
Tightening Torque
70 N•m (52 lb-ft)
Tightening Torque
38 N•m (28 lb-ft)
2. Unscrew the lower engine mounting nut.
Installation Notice
3. Remove the hydraulic engine mounting insulator.
Notice: If the insulator is spotted with oil, replace
the hydraulic insulator asseambly.
4. Installation should follow the removal procedure in
the reverse order.
YAD1B310
YAD1B320
SSANGYONG Y200
1B1-24 M162 ENGINE MECHANICAL
CYLINDER HEAD COVER
1 Ignition Cable Dust Cover
2 Bolt (M6 x 65, 8 pieces)
. . . . . . . . . ... 9-11 N•m (80-97 lb-in)
3 Bolt (M6 x 50, 4 pieces)
. . . . . . . . . ... 9-11 N•m (80-97 lb-in)
4 Spacer Sleeve
5 Thrust Piece
6 Cylinder Head Cover
7 Gasket . . . . . . . . . . . . . Replace
8 Spart Plug Hole Seal . . . . . . . . Replace
9 Camshaft Seal . . . . . . . . . ... Replace
Composition of The Cylinder Head Cover
Bolts
A. M6 x 50, 4 Pieces - Bolts + Washers
B. M6 x 65, 8 Pieces - Bolts + Washers
YAD1B450
YAD1B460
M162 ENGINE MECHANICAL 1B1-25
SSANGYONG Y200
2. Remove the spark plug cover.
Installation Notice
4. Unscrew all the bolts (2,3) and remove the head
cover and the gasket.
Installation Notice
Replace the gasket with a new one if necessary.
5. Installation should follow the removal procedure in
the reverse order.
6. Check for oil leaks by operating the engine.
3. Remove the spark plug connector and ignition
cable.
Removal & Installation Procedure
1. Remove the intake air duct.
Installation Notice
Tightening Torque
9 - 11 N•m
(80 - 97 lb-in)
Tightening Torque
9 - 11 N•m
(80 - 97 lb-in)
Unscrew the seven (M6 x 60) bolts and remove
the spark plug cover.
YAD1B470
YAD1B480
YAD1B490
YAD1B500
Tightening Torque
9 - 11 N•m
(80 - 97 lb-in)
SSANGYONG Y200
1B1-26 M162 ENGINE MECHANICAL
Removal & Installation Procedure
1. Remove the camshaft actuator.
Installation Notice
CYLINDER HEAD FRONT COVER
Preceding Work : Removal of cylinder head cover
Removal of coolant connection fitting
1 Camshaft Position Sensor
2 Camshaft Actuator
3 Upper Guide Rail
4 Bolt (M6 x 60, 3 pieces)
. . . . . . ... 22.5-27.5 N•m (16.6-20.3 lb-ft)
5 Bolt (M8 x 80, 3 pieces)
. . . . . . ... 22.5-27.5 N•m (16.6-20.3 lb-ft)
6 Front Cover
7 Rubber Gasket . . . . . . . . . .. Replace
8 Bolt (M6 x 16, 3 pieces)
. . . . . . . . . . . 9-11 N•m (80-97 lb-in)
Tightening Torque
9 - 11 N•m
(80 - 97 lb-in)
YAD1B510
YAD1B520
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст