SsangYong Rexton. Manual — part 324
M162 ENGINE MECHANICAL 1B1-99
SSANGYONG Y200
1 Bolt (M8 x 20, 1 piece)
. . . . . . . . . . 29-35 N•m (21-26 lb-ft)
2 Sprocket (Oil Pump Drive)
OIL PUMP
Preceding Work : Removal of oil pan
3 Bolt (M8 x 35, 3 pieces)
. . . . . . .. 22.5-27.5 N•m(16.6-20.3 lb-ft)
4 Spring Pin
5 Oil Pump
YAD1B3E0
YAD1B3F0
Removal & Installation Procedure
1. Remove the bolt (1) from the oil pump drive
sprocket (2) and separate the gear and the oil
pump drive chain.
Installation Notice
Tighten the baffle plate and the oil pump with the
two bolts in right side first, and then tighten the
other bolt.
3. Remove the oil pump and oil strainer assembly.
4. Replace the strainer in oil pump if necessary.
5. Installation should follow the removal procedure
in the reverse order.
2. Unscrew the oil pump mounting bolts (3).
Installation Notice
Tightening Torque
29 - 35 N•m
(21 - 26 lb-ft)
Tightening Torque
22.5 - 27.5 N•m
(16.6 - 20.3 lb-ft)
SSANGYONG Y200
1B1-100 M162 ENGINE MECHANICAL
OIL PRESSURE RELIEF VALVE
Preceding Work : Removal of oil pan
1 Screw Plug . . . . . . . ... 50 N•m (37 lb-ft)
2 Compression Spring
Removal & Installation Procedure
1. Remove the screw plug (1).
Installation Notice
2. Remove the spring (2), guide pin (3) and the piston
(4).
3. Installation should follow the removal procedure
in the reverse order.
Notice: Don’t use the seal for the screw plug.
3 Guide Pin
4 Piston
Tightening Torque
50 N•m (37 lb-ft)
YAD1B3G0
M162 ENGINE MECHANICAL 1B1-101
SSANGYONG Y200
OIL NON-RETURN VALVE
Preceding Work : Removal of timing gear case cover
1 Oil Non-return Valve
Functions
The non-return valve prevents the oil in the chain
tensioner from drying up. In other words, it stops oil-
returning in order to prevent the oil in the chain tensioner
from getting dry. As a result, the chain tensioner can
be activated with oil in itself.
Replacement Procedure
1. Remove the non-return valve using a pliers.
2. Insert new non-return valve with hand.
YAD1B3J0
YAD1B3H0
SSANGYONG Y200
1B1-102 M162 ENGINE MECHANICAL
YAD1B3L0
OIL DIPSTICK GUIDE TUBE
1 Oil Dipstick Level Gauge
2 Oil Dipstick Guide Tube
Removal & Installation Procedure
1. Pull out the oil dipstick level gauge (1).
2. Remove the bolt (4) in the upper intake manifold
and remove the oil dipstick guide tube.
Installation Notice
3. Install new O-ring to the dipstick guide tube.
4. Installation should follow the removal procedure
in the reverse order.
5. Check for leaks by starting the engine.
3 O-ring
4 Bolt (M6 x 12, 1 piece) . 9-11 N•m (80-97 lb-in)
Tightening Torque
9 - 11 N•m
(80 - 97 lb-in)
YAD1B3K0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст