Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 253
ENGINE DRIVEABILITY AND EMISSIONS
6E–253
24
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the “SPS (Service Programming System)”.
Was the problem solved?
—
Verify repair
Go to Step 25
25
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual.
Following ECM programming, the immobiliser system
(if equipped) must be linked to the ECM. Refer to
section 11 “Immobiliser System-ECM replacement” for
the ECM/Immobiliser linking procedure.
—
Verify Repair
—
Step
Action
Value(s)
Yes
No
6E–254
ENGINE DRIVEABILITY AND EMISSIONS
DIESELING, RUN-ON SYMPTOM
DEFINITIONS: Engine continues to run after key is turned OFF, but runs very rough. If engine runs smoothly, check
the ignition switch and adjustment.
Step
Action
Value(s)
Yes
No
1
Was the “On-Board Diagnostic (OBD) System Check”
performed?
—
Go to Step 2
Go to OBD
System Check
2
1. Perform a bulletin search.
2. If a bulletin that addresses the symptom is found,
correct the condition as instructed in the bulletin.
Was a bulletin found that addresses the symptom?
—
Verify repair
Go to Step 3
3
Was a visual/physical check performed?
—
Go to Step 4
Go to Visual /
physical Check.
4
Check for a short between battery voltage and the
ignition feed circuit.
Was a problem found?
—
Verify repair
Go to Step 5
5
Check the fuel leaking from injector. Refer to Fuel
System Diagnostic.
Was the problem found?
—
Verify repair
Go to Step 6
6
1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no
malfunctions have been found, review/inspect the
following:
• Visual/physical inspection
• Tech 2 data
• All electrical connections within a suspected
circuit and/or system
Was a problem found?
—
Verify repair
Go to Step 7
7
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the “SPS (Service Programming System)”.
Was the problem solved?
—
Verify repair
Go to Step 8
8
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual.
Following ECM programming, the immobiliser system
(if equipped) must be linked to the ECM. Refer to
section 11 “Immobiliser System-ECM replacement” for
the ECM/Immobiliser linking procedure.
—
Verify repair
—
ENGINE DRIVEABILITY AND EMISSIONS
6E–255
BACKFIRE SYMPTOM
DEFINITIONS: Fuel ignites in the intake manifold, or in the exhaust system, making a loud popping noise.
Step
Action
Value(s)
Yes
No
1
Was the “On-Board Diagnostic (OBD) System Check”
performed?
—
Go to Step 2
Go to OBD
System Check
2
1. Perform a bulletin search.
2. If a bulletin that addresses the symptom is found,
correct the condition as instructed in the bulletin.
Was a bulletin found that addresses the symptom?
—
Verify repair
Go to Step 3
3
Was a visual/physical check performed?
—
Go to Step 4
Go to Visual /
physical Check.
4
Check for proper ignition voltage output with the spark
tester.
Was a problem found?
—
Verify repair
Go to Step 5
5
1. Remove the spark plugs and check for gas or oil
fouling cracks, wear, improper gap, burned
electrodes, heavy deposits, or improper heat
range.
2. If spark plugs are fouled, the cause of fouling must
be determined before replacing the spark plugs.
Was a problem found?
—
Verify repair
Go to Step 6
6
Visually/physically inspect all spark plug high-tension
cables. Check for the following conditions:
• Verify that the resistance of all spark plug high-
tension cables are less than the specified value.
• Verify that the all spark plug high-tension cables are
correctly fitted to eliminate cross-fitting.
• Verify that the all spark plug high-tension cables are
not arcing to ground.
Spraying the spark plug high-tension cables with a
light mist of water may help locate an intermittent
problem.
Was a problem found?
#1 cyl. 4.4k
Ω
#2 cyl. 3.6k
Ω
#3 cyl. 3.1k
Ω
#4 cyl. 2.8k
Ω
Verify repair
Go to Step 7
7
Check the fuel pressure. Refer to Fuel System
Pressure Test.
Was a problem found?
—
Verify repair
Go to Step 8
8
Check for an intermittent ignition system malfunction:
• Intermittent CKP 58X signal
• Intermittent ignition feed circuit or sensor ground
circuit to the crankshaft position sensor.
Was a problem found?
—
Verify repair
Go to Step 9
9
Refer to Fuel System Diagnosis to determine if there
is a problem with fuel delivery.
Was a problem found?
—
Verify repair
Go to Step 10
6E–256
ENGINE DRIVEABILITY AND EMISSIONS
10
Check for the following engine mechanical problems
(refer to Engine Mechanical):
• Low compression
• Leaking cylinder head gaskets
• Worn camshaft
• Sticking or leaking valves
• Valve timing
• Broken valve springs
• Camshaft drive belt slipped or stripped
Was a problem found?
—
Verify repair
Go to Step 11
11
Check leakage at exhaust system.
Check the intake and exhaust manifold for casting
flash. Refer to Engine Mechanical.
Was a problem found?
—
Verify repair
Go to Step 12
12
1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no
malfunctions have been found, review/inspect the
following:
• Visual/physical inspection
• Tech 2 data
• All electrical connections within a suspected
circuit and/or system
Was a problem found?
—
Verify repair
Go to Step 13
13
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the “SPS (Service Programming System)”.
Was the problem solved?
—
Verify repair
Go to Step 14
14
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual.
Following ECM programming, the immobiliser system
(if equipped) must be linked to the ECM. Refer to
section 11 “Immobiliser System-ECM replacement” for
the ECM/Immobiliser linking procedure.
—
Verify repair
—
Step
Action
Value(s)
Yes
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст