Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 45
4JA1-TC/4JH1-TC ENGINE DRIVEABILITY AND EMISSIONS
6E–175
9
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the “SPS (Service Programming System)”.
Was the problem solved?
—
Verify repair
Go to Step 10
10
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual.
Following ECM programming, the immobiliser system
(if equipped) must be linked to the ECM. Refer to
section 11 “Immobiliser System-ECM replacement” for
the ECM/Immobiliser linking procedure.
—
Verify repair
—
Step
Action
Value(s)
Yes
No
6E–176
4JA1-TC/4JH1-TC ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P0381 (Symptom Code 8) (Flash Code 67)
Glow Plug Indicator Circuit Voltage High
Step
Action
Value(s)
Yes
No
1
Was the “On-Board Diagnostic (OBD) System Check”
performed?
—
Go to Step 2
Go to On Board
Diagnostic
(OBD) System
Check
2
1. Connect the Tech 2.
2. Review and record the failure information.
3. Select “F0: Read DTC Infor As Stored By ECU” in
“F0: Diagnostic Trouble Codes”.
Is the DTC P0381 (Symptom Code 8) stored as
“Present Failure”?
—
Go to Step 3
Refer to
Diagnostic Aids
and Go to Step
3
3
1. Using the Tech 2, ignition “On” and engine “Off”.
2. Select “F1: Clear DTC Information” in “F0:
Diagnostic Trouble Codes” with the Tech 2 and
clear the DTC information.
3. Operate the vehicle and monitor the “F0: Read
DTC Infor As Stored By ECU” in the “F0:
Diagnostic Trouble Codes”.
Was the DTC P0381 (Symptom Code 8) stored in this
ignition cycle?
—
Go to Step 4
Refer to
Diagnostic Aids
4
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the “SPS (Service Programming System)”.
Was the problem solved?
—
Verify repair
Go to Step 5
5
Substitute a known good ECM and recheck.
Was the problem solved?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual.
Following ECM programming, the immobiliser system
(if equipped) must be linked to the ECM. Refer to
section 11 “Immobiliser System-ECM replacement” for
the ECM/Immobiliser linking procedure.
—
Go to Step 6
—
6
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual.
Following ECM programming, the immobiliser system
(if equipped) must be linked to the ECM. Refer to
section 11 “Immobiliser System-ECM replacement” for
the ECM/Immobiliser linking procedure.
—
Verify repair
—
4JA1-TC/4JH1-TC ENGINE DRIVEABILITY AND EMISSIONS
6E–177
DIAGNOSTIC TROUBLE CODE (DTC) P0400 (SYMPTOM CODE 3)
(FLASH CODE 32) EXHAUST GAS RECIRCULATION FLOW EXCESSIVE
DETECTED
DIAGNOSTIC TROUBLE CODE (DTC) P0400 (SYMPTOM CODE 4)
(FLASH CODE 32) EXHAUST GAS RECIRCULATION CIRCUIT SHORT TO
GROUND OR OPEN CIRCUIT
DIAGNOSTIC TROUBLE CODE (DTC) P0400 (SYMPTOM CODE 5)
(FLASH CODE 32) EXHAUST GAS RECIRCULATION FLOW INSUFFICIENT
DETECTED
DIAGNOSTIC TROUBLE CODE (DTC) P0400 (SYMPTOM CODE 8)
(FLASH CODE 32) EXHAUST GAS RECIRCULATION CIRCUIT SHORT TO
BATTERY
Batt
µP
Batt
µP
Batt
µP
0.5
BLK/
URG
0.5
BRN/
RED
0.5
BLU/
RED
0.5
BLU/
RED
4JA1-TC
0.5
GRY/
YEL
97
46
61
0.5
WHT/
RED
83
0.5
GRN/
RED
88
0.5
BLK/
RED
92
0.5
BLK/
BLU
84
IAT
Sensor
MAF &
IAT
Sensor
Rr Fog
Light
10A
EGR-
EVRV
0.5
WHT/
BLK
0.5
BLU/
RED
0.5
WHT/
BLU
0.5
BLU/
RED
0.5
GRN/
RED
0.5
BLU/
RED
Exhaust
Throttle
VSV2
Exhaust
Throttle
VSV1
Engine
Warming Up
SW
Thermo
SW
2
4
5
3
1
Battery
Voltage
ECM
Main Relay
IC
IC
IC
CPU
Engine
Control
Module
(ECM)
40
6E–178
4JA1-TC/4JH1-TC ENGINE DRIVEABILITY AND EMISSIONS
Condition for setting the DTC and action taken when the DTC sets
Circuit Description
The amount of EGR is controlled by EVRV (electrical
vacuum regulating valve) via the engine control module
(ECM) command signal depends on the engine speed,
operating of the accelerator pedal and engine coolant
temperature.
The EVRV is shaped to control vacuum applied to the
diaphragm chamber of the EGR valve based on duty
signal sent from the ECM.
If the EGR valve is stuck at open position or close
position, DTC P0400 (Symptom Code 3) or DTC P0400
(Symptom Code 5) is stored.
If the EGR EVRV circuit is open or short ground circuit,
DTC P0400 (Symptom Code 4) is stored.
If the EGR EVRV circuit is short to voltage circuit, DTC
P0400 (Symptom Code 8) is stored.
Diagnostic Aids
An intermittent may be caused by the following:
• Poor connections.
• Misrouted harness.
• Rubbed through wire insulation.
• Broken wire inside the insulation.
• EGR valve sticking.
• Faulty intake air duct connection.
Check for the following conditions:
• Poor connection at ECM-Inspect harness connectors
for backed out terminals, improper mating, broken
locks, improperly formed or damaged terminals, and
poor terminal to wire connection.
• Damaged harness-Inspect the wiring harness for
damage. If the harness appears to be OK, observe
the DTC P0400 display on the Tech2 while moving
connectors and wiring harnesses. A change in the
display will indicate the location of the fault.
Diagnostic Trouble Code (DTC) P0400 (Symptom Code 3) (Flash Code 32)
Exhaust Gas Recirculation Flow Excessive Detected
Flash
Code
Code
Symptom
Code
MIL
DTC Name
DTC Setting Condition
Fail-Safe (Back Up)
32
P0400
3
ON
Exhaust Gas Recirculation
Flow Excessive Detected
1. Intake air temperature is
between 15°C and 100°C.
2. Engine coolant temperature
is between 55°C and
100°C.
3. Barometric pressure is
between 850hpa and
1100hpa.
4. Small amount of mass air
flow. (Desired mass air flow
- mass air flow is more than
150mg/strk)
Fuel injection quantity is
reduced.
4
ON
Exhaust Gas Recirculation
Circuit Short to Ground or
Open Circuit
EGR EVRV circuit open or
short to ground circuit.
Fuel injection quantity is
reduced and EGR EVRV 10%
conditions as substitute.
5
ON
Exhaust Gas Recirculation
Flow Insufficient Detected
1. Intake air temperature is
between 15°C and 100°C.
2. Engine coolant temperature
is between 55°C and
100°C.
3. Barometric pressure is
between 850hpa and
1100hpa.
4. Large mount of mass air
flow. (Desired mass air
flow - mass air flow is below
150 mg/strk)
Fuel injection quantity is
reduced.
8
ON
Exhaust Gas Recirculation
Circuit Short to Battery
EGR EVRV circuit short to
voltage circuit.
Fuel injection quantity is
reduced & EGR EVRV 10%
conditions as substitute.
Step
Action
Value(s)
Yes
No
1
Was the “On-Board Diagnostic (OBD) System Check”
performed?
—
Go to Step 2
Go to On Board
Diagnostic
(OBD) System
Check
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст