Isuzu Rodeo UE. Manual — part 136

6A–33

ENGINE MECHANICAL (X22SE 2.2L)

6. Remove twenty fixing bolts from intake and exhaust

camshaft bracket on the cylinder head, then remove
camshafts.

011RW015

CAUTION:

f

Do not damage camshaft lobe and journal.

f

Do not damage hydraulic lash adjuster(HLA) and
do not allow into foreign materials into cylinder
head.

7. Remove oil seal from camshaft.

Installation

1. Clean surface of camshaft bracket and HLA.
2. Apply engine oil to journal surface of camshaft

bracket and HLA.

3. Install camshaft to cylinder head.
4. Install camshaft bracket according to numerical as

shown in the illustration.
The bracket number is:

f

Exhaust: 1 to 5 from front

f

Intake: 6 to 10 from front.

014RW052

015RW014

6A–34

ENGINE MECHANICAL (X22SE 2.2L)

Camshaft oil seal installation area on the cylinder
body of No.1, No.6 and camshaft bracket rear side
plug portion must be applied HN1023 or equivalent as
in the illustration.

014RW073

5. Tighten camshaft bracket bolts to the specified torque

by sequence in the illustration.

Torque: 8 N·m (5.9 lb ft)

6. Use J–42609 for installation camshaft oil seal.

014RW075

014RW071

7. Install the camshaft drive gear. Align the timing mark

between notch on the camshaft drive gear(1) and lug
on the camshaft bracket(2).

014RW076

6A–35

ENGINE MECHANICAL (X22SE 2.2L)

Also align a guide hole on the camshaft drive gear
marked “IN” for intake and “EX” for exhaust to guide
pin on the camshaft when instaling the camshaft drive
gear.

014RW072

8. Tighten camshaft bracket fixing bolt to the specified

torque.

Torque: 50 N·m (36 lb ft)

015RW014

9. Install timing belt.

Refer to installation procedure for Timing Belt in this
manual.

10. Install cylinder head cover.

Refer to installation procedure for Cylinder Head
Cover in this manual.

11. Connect battery ground cable.

Engine Assembly

515RX002

6A–36

ENGINE MECHANICAL (X22SE 2.2L)

Removal

1. Disconnect battery ground and positive cable.
2. Remove battery.
3. Make alignment mark on the engine hood and hinges

before removal in order to return the hood to original
position exactly.

4. Remove engine hood.
5. Drain engine coolant from radiator.
6. Disconnect throttle valve control cable from throttle

valve on intake manifold.

7. Remove air duct with air cleaner cover.
8. Remove air cleaner assembly.
9. Disconnect three engine harness connectors from

chassis harness of left rear side engine compartment.

10. Disconnect vacuum hose on the brake booster.

11. Disconnect cooling fan harness connector on the left

of fan shroud.

12. Disconnect ground cable connector from left and right

of front wheel arch upper side.

13. Remove clutch piping bracket from right side of clutch

housing.

14. Remove fuel piping bracket from transmission.
15. Remove four nuts from exhaust front pipe exhaust

manifold side and remove two bolts from rear side of
exhaust front pipe. Remove exhaust front pipe.

027RW005

16. Remove transmission mounting fixing bolts and nut

from cross member.

022RW014

17. Remove transmission front under cover from front

portion of clutch housing.

18. Disconnect two fuel pipes at right side of transmission

by quick type fuel hose connector.

CAUTION: Plug fuel pipe on engine side and fuel
hose from fuel tank.

19. Disconnect canister hose next to fuel piping

connector.

20. Remove propeller shaft fixing bolt from rear side

transmission.

21. Remove fixing bolts between clutch housing and

transmission, then move transmission.

22. Remove power steering pump assembly then place

the power steering pump along with piping.

23. Disconnect two chassis harness connectors from

right rear side engine compartment (under fuse box)
and remove two harness clips.

24. Remove engine ground cable from chassis frame.
25. Remove radiator lower hose from engine side.
26. Remove two heater hoses from right side panel.
27. Remove radiator grille.
28. Remove harness clip from behind right horn.
29. Remove engine mounting bolt from chassis frame

side.