Isuzu Rodeo UE. Manual — part 89
TRANSFER CASE
4D–19
Detent, Shift Arm, and Interlock Pin (Transfer Case Assembly)
Disassembled View
262RW005
Legend
(1) Detent Ball, Spring and Plug
(2) Spring Pin and Bridge
(3) Spring Pin
(4) Spring
(5) 2WD–4WD Shift Rod
(6) Shift Arm
(7) Shift Block
(8) 4WD Indicator Switch
(9) Interlock Pin
(10) Spring
(11) Select Rod Assembly
(12) Spring Pin
(13) High–Low Shift Rod
(14) Shift Arm
(15) Shift Block
(16) Transfer Case
4D–20
TRANSFER CASE
Disassembly
1. Remove detent ball, spring and plug (1).
2. Use a spring pin remover to remove the spring pin (2)
from the bridge (6).
262RW011
3. Remove spring (4).
4. Engage the 2WD–4WD sleeve with front output gear.
Remove the spring pin (3) from the block (7). Remove
the shift rod (5).
262RW022
5. Remove shift arm (6).
6. Remove shift block (7).
7. Remove 4WD indicator switch (8).
8. Use a magnetic tool to remove the interlock pin (9)
and spring (10) from the transfer case (16).
262RS005
9. Remove select rod assembly (11).
10. Use a spring pin remover to remove the shift arm
spring pin (12) from the shift arm (14) and shift block
(15). Remove the high–low shift rod (13) from transfer
case (16).
262RS006
11. Remove shift arm (14).
12. Remove shift block (15) from transfer case (16).
TRANSFER CASE
4D–21
Inspection and Repair
Refer to “TRANSFER CASE ASSEMBLY” in this section
for inspection and repair.
Reassembly
1. Place shift block (15) in transfer case (16).
2. Set shift arm (14) on the High–Low sleeve.
3. Push High–Low shift rod (13) through shift arm (14)
and block (14).
4. Engage the High–Low sleeve with the 4H (1) side.
5. Install the spring pin (12) to the shift block (15) and
shift arm (14).
262RW034
6. Install select rod assembly (11), joining its lever to
shift block groove.
7. Engage the High–Low sleeve with the 4H side and
install the interlock pin and spring (10) in the proper
direction.
8. Place 2WD–4WD shift block in the transfer case (16).
9. Set 2WD–4WD shift arm on the 2WD–4WD sleeve.
10. Puh 2WD–4WD shift rod through 2WD–4WD shift
arm and 2WD–4WD shift block.
11. Install the shift rod: 2WD–4WD (5) with interlock pin
pushed in.
262RW035
Legend
(18) 2WD–4WD
(19) 4H Side
(20) Interlock pin
(21) 2WD
(22) 4WD
(23) Rod: 2–4
(24) Rod: H–L
(25) 4H
(26) 4L
(27) 4
×
2
(28) 4
×
4
4D–22
TRANSFER CASE
12. Install 4WD indicator switch and gasket (8).
Tighten to the specified torque.
Torque: 39 N·m (29 lb ft)
13. Install spring (4).
14. Engage the 2WD–4WD sleeve with the 4WD side and
install the spring pin (3).
262RW022
15. Install spring pin (2) and bridge (2).
16. Install detent ball, spring and plug and tighten the plug
to the specified torque.
Torque: 25 N·m (18 lb ft)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст