Isuzu KB P190. Manual — part 88

FRONT SUSPENSION 3C-31

Shock Absorber

Shock Absorber and Associated Parts

RTW340MF000901

Legend

(1) Shock Absorber Nut

(2) Rubber Bushing and Washer

(3) Shock Absorber Bolt and Nut

(4) Shock Absorber

(5) Rubber Bushing and Washer

Removal

1. Raise the vehicle and support it with suitable

safety stands.

2. Remove wheel and tire assembly. Refer to Wheel

Replacement in this section.

3. Remove bolt and nut.

4. Remove nut.

5. Remove rubber bushing and washer.

6. Remove shock absorber.

7. Remove rubber bushing and washer.

Inspection and Repair

Make necessary correction or replace parts if wear,
damage, corrosion or any other abnormal condition is
found through inspection.

Check the following parts:

• Shock

absorber

• Rubber bushing

Installation

1. Install rubber bushing and washer.

2. Install shock absorber.

3. Install rubber bushing and washer.

4. Install shock absorber nut, then tighten it to the

specified torque.

Torque: 20 N

⋅⋅⋅⋅m (2.0 kgf⋅⋅⋅⋅m/14 lb⋅⋅⋅⋅ft)

5. Install shock absorber bolt and nut, and then

tighten to the specified torque.

Torque: 93 N

⋅⋅⋅⋅m (9.5 kgf⋅⋅⋅⋅m/69 lb⋅⋅⋅⋅ft)

3C-32 FRONT SUSPENSION

Stabilizer Bar

Stabilizer Bar and Associated Parts

RTW340MF000401

Legend

(1) Rubber Bushing

(2) Bracket and Bolt

(3)

Link

(4) Link Nut

(5) Stabilizer Bar

(6) Link Nut

Removal

1. Raise the vehicle and support the frame with

suitable safety stands.

2. Remove the stone guard.

3. Remove wheel and tire assembly. Refer to Wheel

Replacement in this section.

4. Remove link nut.

CAUTION: Be careful not to break the ball joint
boot.

5. Remove link.

6. Remove bracket.

7. Remove stabilizer bar.

8. Remove rubber bushing.

Inspection and Repair

Make necessary correction or replace parts if wear,
damage, corrosion or any other abnormal condition is
found through inspection.
Check the following parts:

• Stabilizer

bar

• Rubber

bushing

• Link ball joint

FRONT SUSPENSION 3C-33

Installation

1. Install rubber bushing.

2. Install stabilizer bar.

3. Install bracket and bolt then tighten it to the

specified torque.

Torque: 25 N

⋅⋅⋅⋅m (2.5 kgf⋅⋅⋅⋅m/18 lb⋅⋅⋅⋅ft)

4. Install link.

5. Install link nut, then tighten it to the specified

torque.

Torque: 50 N

⋅⋅⋅⋅m (5.1 kgf⋅⋅⋅⋅m/37 lb⋅⋅⋅⋅ft)

3C-34 FRONT SUSPENSION

Torsion Bar

Torsion Bar and Associated Parts

RTW340MF000501

Legend

(1) Adjust Bolt, End Piece and Seat

(2) Height Control Arm

(3) Torsion Bar

Removal

1. Raise the vehicle and support the frame with

suitable safety stands.

2. Apply the setting marks (1) to the adjust bolt and

end piece, then remove adjust bolt, end piece and

seat.

410RS004