Nissan Almera Tino V10. Manual — part 574
EC-1122
[YD (WITH EURO-OBD)]
DTC P0340 CMP SENSOR
5.
Check resistance as shown in the figure.
6.
If NG, replace camshaft position sensor.
Removal and Installation
EBS013D3
CAMSHAFT POSITION SENSOR
Refer to
.
Terminal No. (Polarity)
Resistance
Ω
[at 25
°
C (77
°
F)]
3 (+) - 1 (-)
Except 0
3 (+) -2 (-)
2 (+) - 1 (-)
Except 0 or
∞
MBIB0616E
DTC P0341 CMP SENSOR
EC-1123
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0341 CMP SENSOR
PFP:23731
Description
EBS013D4
The camshaft position sensor identifies a particular cylinder by
means of signals from the sensing plate (with five protrusions)
installed to the camshaft. The datum signal output is detected 90
°
signal and sent to the ECM.
ECM Terminals and Reference Value
EBS013D5
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
On Board Diagnosis Logic
EBS013D6
MBIB0618E
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage and Pulse Signal)
45
R
Camshaft position sensor
power supply
[Ignition switch ON]
Approximately 5.3V
47
B
Camshaft position sensor
[Engine is running]
●
Warm-up condition
●
Idle speed
0 - 6V
[Engine is running]
●
Warm-up condition
●
Engine speed is 2,000 rpm
0 - 6V
66
W
Camshaft position sensor
ground
[Ignition switch ON]
Approximately 0.3V
67
B
Sensor ground
(Sensors shield circuit)
[Ignition switch ON]
Approximately 0.3V
MBIB0877E
MBIB0878E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0341
Camshaft position sensor
circuit range/performance
Camshaft position sensor signal is not in the
normal pattern when engine is running.
●
Harness connectors
(The sensor circuit is opener shorted.)
●
Camshaft position sensor
●
Signal plate
EC-1124
[YD (WITH EURO-OBD)]
DTC P0341 CMP SENSOR
DTC Confirmation Procedure
EBS013D7
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for at least 5 seconds.
If engine could not start, keep ignition switch at START position
for 5 seconds.
4.
If 1st trip DTC is detected, go to
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF817Y
DTC P0341 CMP SENSOR
EC-1125
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS013D8
YEC505A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст