Nissan Almera Tino V10. Manual — part 198
AT-516
[ALL]
ASSEMBLY
18. Install control valve assembly.
a.
Insert manual valve into control valve assembly.
●
Apply ATF to manual valve.
b.
Pass solenoid harness through transmission case and install
terminal body on transmission case by pushing it.
c.
Install stopper ring to terminal body.
d.
Tighten bolts A , B and C .
Bolt length, number and location:
SAT017D
AAT261A
: 7 - 9N·m (0.7 - 0.9 kg-m, 61 - 78 in-lb)
Bolt
A
B
C
Bolt length “
”
40 mm
(1.57 in)
33 mm
(1.30 in)
43.5 mm
(1.713 in)
Number of bolts
5
6
2
AAT260A
ASSEMBLY
AT-517
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
19. Install oil pan.
a.
Attach a magnet to oil pan.
b.
Install new oil pan gasket on transmission case.
c.
Install oil pan on transmission case.
●
Always replace oil pan bolts as they are self-sealing
bolts.
●
Tighten four bolts in a criss-cross pattern to prevent dis-
location of gasket.
d.
Tighten drain plug to specified torque.
20. Install park/neutral position (PNP) switch.
a.
Set manual shaft in P position.
b.
Temporarily install park/neutral position (PNP) switch on manual
shaft.
c.
Move selector lever to N position.
d.
Use a 4 mm (0.16 in) pin for this adjustment.
i.
Insert the pin straight into the manual shaft adjustment hole.
ii.
Rotate park/neutral position (PNP) switch until the pin can also
be inserted straight into hole in park/neutral position (PNP)
switch.
e.
Tighten park/neutral position (PNP) switch fixing bolts. Refer to
.
f.
Remove pin from adjustment hole after adjusting park/neutral
position (PNP) switch.
SAT418D
SAT128E
SAT023JB
SAT426DB
AT-518
[ALL]
ASSEMBLY
21. Install A/T fluid charging pipe and fluid cooler tube to transmis-
sion case. Tighten A/T fluid charging pipe and fluid cooler tube
bolts to the specified torque. Refer to
.
22. Install torque converter.
a.
Pour ATF into torque converter.
●
Approximately 1 liter (1-3/4 Imp pt) of fluid is required for
a new torque converter.
●
When reusing old torque converter, add the same amount
of fluid as was drained.
b.
Install torque converter while aligning notches of torque con-
verter with notches of oil pump.
c.
Measure distance “A” to check that torque converter is in proper
position.
MCIB9012E
SAT428DA
SAT429D
Distance A:
Refer to
AT-519, "SERVICE DATA AND SPECIFICA-
.
SAT430D
SERVICE DATA AND SPECIFICATIONS (SDS)
AT-519
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
General Specifications
ECS009CZ
*: Refer to MA-13, “Recommended Fluids and Lubricants”.
Shift Schedule
ECS009D0
VEHICLE SPEED WHEN SHIFTING GEARS
VEHICLE SPEED WHEN PERFORMING LOCK-UP
Stall Revolution
ECS009D1
Line Pressure
ECS009D2
Engine
QG18DE
Automatic transaxle model
RE4F03B
Automatic transaxle assembly
Model code number
3AX70
Transaxle gear ratio
1st
2.861
2nd
1.562
3rd
1.000
4th
0.697
Reverse
2.310
Final drive
4.072
Recommended fluid
Genuine Nissan Automatic Transmission
Fluid or equivalent*
Fluid capacity
7.7
(6-3/4 Imp qt)
Throttle posi-
tion
Shift pattern
Vehicle speed km/h (MPH)
D
1
→
D
2
D
2
→
D
3
D
3
→
D
4
D
4
→
D
3
D
3
→
D
2
D
2
→
D
1
1
2
→
1
1
Full throttle
Comfort
54 - 62
(20 - 23)
102 - 110
(64 - 69)
162 - 170
(96 - 100)
158 - 166
(99 - 104)
92 - 100
(57 - 63)
41 - 49
(25 - 30)
54 - 62
(34 - 39)
Half throttle
Comfort
29 - 37
(18 - 23)
51 - 59
(32 - 37)
123 - 131
(77 - 80)
69 - 77
(43 - 48)
34 - 42
(21 - 26)
5 - 13
(3 - 8)
54 - 62
(34 - 39)
Throttle opening
OD switch
Shift pattern
Vehicle speed km/h (MPH)
Lock-up ON
Lock-up OFF
2/8
ON (D
4
)
Comfort
96 - 104 (60 - 65)
65 - 73 (41 - 46)
OFF (D
3
)
Comfort
96 - 104 (60 - 65)
93 - 101 (58 - 63)
Engine model
Stall revolution rpm
QG18DE
2,300 - 2,750
Engine speed
rpm
Line pressure
kPa (bar, kg/cm
2
, psi)
R position
D position
2 position
1 position
Idle
778 (7.8, 7.9, 113)
500 (5.0, 5.1, 73)
500 (5.0, 5.1, 73)
500 (5.0, 5.1, 73)
Stall
1,813 (18.1, 18.5, 263)
1,165 (11.7, 11.9, 169)
1,165 (11.7, 11.9, 169)
1,165 (11.7, 11.9, 169)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст