Nissan Murano Z51. Manual — part 1454
OIL PAN
TM-167
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6.
Remove oil pan gasket (1) from oil pan (2).
7.
Remove magnet (3) from oil pan.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket mounting surface of
transaxle case and oil pan.
• Never reuse oil pan gasket, O-ring and oil pan fitting bolts.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000005514114
Check foreign materials in oil pan to help determine causes of malfunction. If the CVT fluid is very dark, smells
burned, or contains foreign particles, frictional material (clutches) may need replacement. A tacky film that will
not wipe clean indicates varnish build up. Varnish can cause valves and clutches to stick and can inhibit pump
pressure.
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
SCIA8219J
TM-168
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
SECONDARY SPEED SENSOR
SECONDARY SPEED SENSOR
Exploded View
INFOID:0000000005514115
Removal and Installation
INFOID:0000000005514116
REMOVAL
1.
Disconnect the battery cable from negative terminal.
2.
Remove air duct (inlet). Refer to
3.
Remove air cleaner case. Refer to
4.
Disconnect secondary speed sensor connector.
5.
Remove secondary speed sensor (1) and shim (2).
CAUTION:
Never lose the shim.
6.
Remove O-ring (3) from secondary speed sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000005514117
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
1.
Secondary speed sensor
2.
Shim
3.
Transaxle assembly
4.
O-ring
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JPDIA0687GB
JPDIA0617ZZ
DIFFERENTIAL SIDE OIL SEAL
TM-169
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIFFERENTIAL SIDE OIL SEAL
2WD
2WD : Exploded View
INFOID:0000000005514118
2WD : Removal and Installation
INFOID:0000000005514119
REMOVAL
1.
Remove front drive shafts. Refer to
.
2.
Remove differential side oil seals (1) using a flat-bladed screw-
driver (A).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Drive each differential side oil seal evenly using a commercial ser-
vice tool so that differential side oil seal protrudes by the dimension
(C) respectively.
Unit: mm (in)
NOTE:
Differential side oil seal pulling direction is used as the reference.
1.
RH differential side oil seal
2.
LH differential side oil seal
3.
Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JPDIA0593ZZ
JPDIA0118ZZ
A
: Transaxle case side
B
: Converter housing side
Dimension C
0
±
0.5 (0
±
0.020)
JPDIA0618ZZ
TM-170
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
DIFFERENTIAL SIDE OIL SEAL
CAUTION:
• Never reuse differential side oil seals.
• Apply CVT fluid to differential side oil seals.
Drift to be used:
2WD : Inspection
INFOID:0000000005514120
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
AWD
AWD : Exploded View
INFOID:0000000005514121
AWD : Removal and Installation
INFOID:0000000005514122
REMOVAL
1.
Remove exhaust front tube. Refer to
2.
Separate propeller shaft. Refer to
3.
Remove front drive shafts. Refer to
.
4.
Remove transfer from transaxle assembly. Refer to
Location
Tool number (Kent-Moore No.)
Transaxle case side
ST33400001 (J-26082)
Converter housing side
1.
Side oil seal (transfer joint)
2.
LH differential side oil seal
3.
Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JPDIA0594ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст