Nissan Murano Z51. Manual — part 1455
DIFFERENTIAL SIDE OIL SEAL
TM-171
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5.
Remove differential side oil seal (1) and side oil seal (transfer
joint) using a flat-bladed screwdriver (A).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Drive each differential side oil seal and side oil seal (transfer joint)
evenly using a commercial service tool so that differential side oil
seal and side oil seal (transfer joint) protrudes by the dimension
(C) respectively.
Unit: mm (in)
NOTE:
Differential side oil seal and side oil seal (transfer joint) pulling direc-
tion is used as the reference.
CAUTION:
• Never reuse differential side oil seals and side oil seal (transfer joint).
• Apply CVT fluid to differential side oil seals and side oil seal (transfer joint).
Drift to be used:
AWD : Inspection
INFOID:0000000005514123
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
JPDIA0118ZZ
A
: Transaxle case side
B
: Converter housing side
Dimension C
0
±
0.5 (0
±
0.020)
JPDIA0619ZZ
Location
Tool number (Kent-Moore No.)
Differential side oil seal
ST33400001 (J-26082)
Side oil seal (transfer joint)
KV40100621 (J-25405)
TM-172
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded View
INFOID:0000000005514124
Removal and Installation
INFOID:0000000005514125
REMOVAL
1.
Remove air duct (inlet). Refer to
2.
Remove air cleaner case. Refer to
.
3.
Remove air breather hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Check that air breather hose is not collapsed or blocked due to folding or bending when installed.
• Install air breather hose to air breather tube so that the paint mark
(A) faces upward. Also insert hose to the bend of air breather tube.
1.
Air cleaner case
2.
Air breather hose
3.
Transaxle assembly
4.
Heater pipe
: Vehicle front
JPDIA0592ZZ
SCIA7584J
TRANSAXLE ASSEMBLY
TM-173
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000005514126
Removal and Installation
INFOID:0000000005514127
WARNING:
Never remove the reservoir tank cap when the engine is hot. Serious burns could occur from high-
pressure engine coolant escaping from the reservoir tank.
CAUTION:
• Perform this step engine is cold.
• When replacing TCM and transaxle assembly as a set, replace transaxle assembly first and then
replace TCM. Refer to
TM-8, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Service
After Replacing TCM and Transaxle Assembly"
1.
Air breather hose
2.
CVT fluid level gauge
3.
CVT fluid charging pipe
4.
O-ring
5.
Copper washer
6.
fluid cooler tube
7.
Transaxle assembly
A.
For tightening torque, refer to
TM-173, "Removal and Installation"
.
Refer to
for symbols in the figure.
JPDIA0626GB
TM-174
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
TRANSAXLE ASSEMBLY
REMOVAL
1.
Remove the engine, the transaxle, transfer (AWD models) assembly and front suspension member. Refer
to
(2WD),
(AWD).
2.
Lift with hoist and separate engine, transaxle and transfer (AWD models) assembly from front suspension
member. Refer to
(2WD),
(AWD).
3.
Remove air breather hose. Refer to
4.
Disconnect secondary speed sensor connector. Refer to
.
5.
Disconnect CVT unit connector.
6.
Disconnect air fuel ratio sensor 1 (bank 2). Refer to
.
7.
Remove crankshaft position sensor (POS). Refer to
8.
Remove CVT fluid charging pipe from transaxle assembly.
9.
Remove transaxle assembly fixing bolts with power tool.
10. Remove transaxle assembly from engine assembly with a hoist.
11. Remove CVT fluid cooler hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Check fitting of dowel pins (
) when installing transaxle
assembly to engine assembly.
When installing CVT fluid cooler tube (1) to transaxle assembly:
• Contact CVT fluid cooler tube a boss portion (A) of the transaxle
case.
• Tighten the bolt of CVT fluid cooler tube without moving the CVT
fluid cooler tube.
JPDIA0598ZZ
JPDIA0602ZZ
JPDIA0628ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст