Nissan Murano Z51. Manual — part 1257
B2607 STEERING LOCK RELAY
SEC-75
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
3.
CHECK STEERING LOCK UNIT CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between steering lock unit harness connector and IPDM E/R harness connector.
4.
Check continuity between steering lock unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-35, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
4.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
>> INSPECTION END
Steering lock unit
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M12
1
E10
11
Existed
Steering lock unit
Ground
Continuity
Connector
Terminal
M12
1
Not existed
SEC-76
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2608 STARTER RELAY
B2608 STARTER RELAY
Description
INFOID:0000000005515552
Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition
switch is in START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communication.
DTC Logic
INFOID:0000000005515553
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
• If DTC B2608 is displayed with DTC B210D for IPDM E/R, first perform the trouble diagnosis for DTC
B210D. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005515554
1.
CHECK BCM POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK STARTER RELAY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and BCM harness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2608
STARTER RELAY
BCM receives starter relay ON signal (CAN) from
IPDM E/R even if BCM turns the starter relay OFF.
• Harness or connectors
(starter relay circuit is open or
shorted.)
• IPDM E/R
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M121
52
Ground
Selector lever
N or P position
Battery voltage
Other than above
0
B2608 STARTER RELAY
SEC-77
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-35, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
3.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
>> INSPECTION END
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E11
46
M121
52
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E11
46
Not existed
SEC-78
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2609 STEERING STATUS
B2609 STEERING STATUS
Description
INFOID:0000000005515555
There are 2 switches in the steering lock unit (steering lock/unlock switch 1 and 2). BCM compares those 2
switches conditions to judge the present steering status.
DTC Logic
INFOID:0000000005515556
DTC DETECTION LOGIC
NOTE:
• If DTC B2609 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2609 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE 1
1.
Turn ignition switch ON under the following conditions and wait for at least 1 second.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE 2
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF.
3.
Press driver side door switch and wait for at least 1 second.
4.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005515557
1.
INSPECTION START
Perform inspection in accordance with procedure that confirms DTC.
Which procedure confirms DTC?
DTC confirmation procedure 1>>GO TO 2.
DTC confirmation procedure 2>>GO TO 6.
2.
CHECK BCM OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect steering lock unit connector and IPDM E/R connector.
3.
Check voltage between steering lock unit harness connector and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2609
S/L STATUS
BCM detects the malfunction of steering lock unit
switches for 1 second.
• Harness or connectors
[steering lock unit circuit (BCM
side) is open or shorted]
• Harness or connectors
[steering lock unit circuit (IPDM E/
R side) is open or shorted.]
• Steering lock unit
• IPDM E/R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст