Nissan Murano Z51. Manual — part 795
FSU-4
< PRECAUTION >
PRECAUTIONS
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
FOR USA AND CANADA : Precaution for Procedure without Cowl Top Cover
INFOID:0000000005565574
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
FOR USA AND CANADA : Precautions for Suspension
INFOID:0000000005514310
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Spilled oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing. Since new self-lock nuts are pre-oiled,
tighten as they are.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
INFOID:0000000005565518
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR MEXICO : Precaution Necessary for Steering Wheel Rotation after Battery Dis-
PIIB3706J
PRECAUTIONS
FSU-5
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
connect
INFOID:0000000005565536
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
FOR MEXICO : Precaution for Procedure without Cowl Top Cover
INFOID:0000000005565575
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
FOR MEXICO : Precautions for Suspension
INFOID:0000000005514314
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Spilled oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing. Since new self-lock nuts are pre-oiled,
tighten as they are.
PIIB3706J
FSU-6
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000005514315
The actual shapes of Kent-More tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000005514316
Tool number
(Kent-More No.)
Tool name
Description
ST35652000
(
—
)
Strut attachment
Disassembling and assembling strut
ZZA0807D
Tool name
Description
Spring compressor
Removing and installing coil spring
Power tool
Loosening bolts and nuts
S-NT717
PBIC0190E
FRONT SUSPENSION ASSEMBLY
FSU-7
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
PERIODIC MAINTENANCE
FRONT SUSPENSION ASSEMBLY
Inspection
INFOID:0000000005514317
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, backlash) of each component and component conditions
(wear, damage) are normal.
BALL JOINT AXIAL END PLAY
1.
Set front wheels in a straight-ahead position.
2.
Measure axial end play by prying it up/down with iron bar or equivalent between transverse link and steer-
ing knuckle.
CAUTION:
• Never depress brake pedal when measuring.
• Never perform with tires on level ground.
• Be careful not to damage ball joint boot. Never damage the installation position by applying
excessive force.
STRUT ASSEMBLY
Check for oil leakage, damage, and replace if necessary.
Axial end play
: Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст