Nissan Murano Z51. Manual — part 793
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
2.
Start engine and let it idle and check there are no fuel leakage at the fuel system connections.
FL-12
< REMOVAL AND INSTALLATION >
FUEL TANK
FUEL TANK
Exploded View
INFOID:0000000005515875
• In regard to the notation of torque in the figure, (A) shows an ISO standard, (B) shows a conventional stan-
dard.
Removal and Installation
INFOID:0000000005515876
WARNING:
Be sure to read “General Precautions” when working on the fuel system. Refer to
.
REMOVAL
• Drain fuel from fuel tank if necessary. Refer to
FL-6, "Removal and Installation"
.
• Perform work on level place.
1.
Perform steps 2 to 7 of “REMOVAL” in “ FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP
ASSEMBLY” on main and sub fuel level sensor units. Refer to
FL-6, "Removal and Installation"
.
2.
Remove center muffler. Refer to
1.
Clamp
2.
EVAP/Vent line hose
3.
Fuel tank
4.
Fuel tank mounting band (RH)
5.
Fuel tank protector
6.
Fuel tank protector (RH)
7.
Fuel tank protector (LH)
8.
Fuel tank mounting band (LH)
9.
Clamp
10. Clamp
11.
Fuel filler hose
12. EVAP (Recirculation) hose
13. Clamp
14.
Fuel filler tube
15. Grommet
16. Fuel filler cap
A.
The measurement of hexagonal
width across flat: 16 mm (0.63 in)
B.
The measurement of hexagonal
width across flat: 17 mm (0.67 in)
C.
AWD 20 inch tire models (up to VIN
No. JN8AZ18W79W125941)
Refer to
for to symbols in the figure.
JPBIA2661GB
FUEL TANK
FL-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
3.
Remove propeller shaft. Refer to
. (AWD models)
4.
Remove parking rear brake cables. Refer to
5.
Remove rear suspension member assembly. Refer to
. (AWD models)
NOTE:
For this service, drive shaft, final drive, and rear suspension member are required not to be separate one
another during removal.
6.
Remove fuel tank protectors.
7.
Disconnect fuel filler hose (1), EVAP/Vent line hose (3), and
EVAP (Recirculation) hose (2) from the side other than the fuel
tank side.
8.
Support the lower part of fuel tank (1) with transmission jack (A).
CAUTION:
Support the position that fuel tank mounting bands never
engage.
9.
Remove fuel tank mounting bands.
10. Supporting with hands, descend transmission jack carefully, and remove fuel tank.
CAUTION:
• Check that all connection points have been disconnected.
• Confirm there is no interference with vehicle.
11. Remove fuel filler tube if necessary.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Surely clamp fuel hoses and insert hose to the length below.
• Be sure hose clamp is not placed on swelled area of fuel tube.
• Tighten the clamp hand with the top mark (A) until the mark is on
the bolt head flange.
: Vehicle front
JPBIA1696ZZ
JPBIA0145ZZ
Fuel filler hose
: 35 mm (1.38 in)
The other hoses
: 25 mm (0.98 in)
JPBIA0146ZZ
FL-14
< REMOVAL AND INSTALLATION >
FUEL TANK
• To connect quick connector, refer to
FL-6, "Removal and Installation"
.
Inspection
INFOID:0000000005515877
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leakage.
1.
Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pres-
sure to fuel piping.
2.
Start engine and rev it up and check there are no fuel leakage at the fuel system tube and hose connec-
tions.
• After removing/installing rear suspension assembly, check to adjust wheel alignment and then, adjust neutral
position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст